phone/ipod Touch Users please go to App Store and download any of this apps Rev、SpeedPort、DashCommand

Features:

WI-FI OBD AUTO CHECKER is capable of communicating with vehicles which adopt following protocols:

ISO 9141

ISO 11898(aka. CAN)

ISO 14230(aka. KWP2000)

ISO 15765(aka. CAN)

SAE J1939

WiFi ELM327 works on all 1996 and newer vehicles (cars and light trucks) sold in the United States，including:

Acura	Daihatsu	Isuzu	Mercedes	Porsche	Smart
Alfa Romeo	Daimler	Jaguar	Mercury	Regal	Subaru
Ariel Atom	Dodge	Jeep	MG	Renault	Suzuki
Aston Martin	Ferrari	Kia	Mini	Rolls-Royce	Tesla
Audi	Fiat	Lamborghini	Mitsubishi	Roush	Toyota
Bentley	Ford	Lancia	Nissan	Rover	Triumph
BMW	Geo	Land Rover	Oldsmobile	Saab	TVR
Buick	GMC	Lexus	Opel	Saleen	Vauxhall
Cadillac	Holden	Lincoln	Pagani	Saturn	Volkswagen
Chevrolet	Honda	Lotus	Panoz	Seat	Volvo
Chrysler	Hummer	Maserati	Peugeot	Scion	Yugo
Citroen	Hyundai	Mazda	Plymouth	Shelby	……
Daewoo	Infiniti	McLaren	Pontiac	Skoda	……

able to detect and interpret these protocols automatically. It also provides support for high speed communications and a low power sleep mode. It use AT commands to communicate with a host device (PC， notebook， iPhone， iPod touch， iPad and so on). There are plenty of software packages available， which are fully compatible with WI-FI OBD AUTO CHECKER. Some of them have pretty useful features， such as engine running parameters monitoring， DTC reading and clearing， MPG meter， etc. You can even write your own software on a specified hardware platform if you wish， because the AT commands are fully documented and very well explained.

Display the followting datas:

Vehicle Speed

RPM

Fuel Consumption*

Engine Coolant Temp

Fuel Pressure

Calculated Engine Load

Throttle Position

Intake Manifold Pressure

Air Intake Temp

Timing Advance

Mass Air Flow

Fuel Level

Barometric Pressure

EVAP System Vapor Pressure

Fuel Trim Please note that your vehicle may not support all above parameters. How many parameters you can get depends on the vehicle manufacturer's implementation.

Specifics:

·SSID: WiFiOBD

·IP: 192.168.0.10

·Subnet: 255.255.255.0

·Port: 35000

·Range: 50 ft (Line of sight)

·Antenna: Internal

·Power Consumption: 0.75 Watts (With Power Switch)

·Wifi Standard: 802.11a/b/g

·Operating Temperature: -15 to 100 Deg Celsius

·Plastic: Automotive Grade

·Physical Dimensions: 2.75 x 1.25 x 1.2 inches

Compatible Software and Features:

What features you can have depended on what software you install on iPhone /iPod touch /iPad/ PC. There are a lot of commercial or free software. The features of the software differ from one another. User should choose his own software by his preference. For more details about the software， please consult the software vendors.

Where can I get the software?

You can log on to the apple application store to get your commercial/free software.

There is a freeware in the CD-ROM comes along with the device. You can use this piece of software to config and test the wifi OBO auto checker.

Package Include:

·1 x ELM327 WiFi Wireless OBD2 Interface

·1 x Software CD

Troubleshooting Tips

If you cannot find the Scanner’s WiFi signal in Wireless Settings:

Check to see if the LED lights are on. Some of the LEDs will flicker to indicate a Wi-Fi signal
If your ignition is not on， turn your car key to the 2nd click to turn on the ignition and try again
If the ignition is on， start the engine and try again

If you can connect to the WiFi signal， but cannot connect within the App:

Make sure the connection is configured within the App’s settings. The IP should be 192.168.0.10 and the Port is 35000
In the iPhone settings， touch the blue arrow on the “WiFiOBD” connection. By default， it will connect to the DHCP settings. Set it to Static and enter the IP Address “192.168.0.10” and Subnet Mask to “255.255.255.0”. Try again within the App.