Item Descriptions:

size:

90CM × 200CM

NO.052 Scrub / Opaque / Black / Light Shield / Heat Shield, UV Cut

Black · 100% opaque

It is black and completely opaque glass film, so it will not be visible from the outside after pasting.

It protects the privacy properly, and it can cut the light firmly.

Blindfold / lightproof

With outstanding light shielding, indoor light will not leak out at all even at night.

The pasted part is completely black and can completely block light, so the amount of light coming into the room is reduced and gentle.

Light leakage from the blackout curtain can be avoided.

No rubber

There is no odor, it is environmentally friendly, with an electrostatic type in which adhesive is unnecessary.

You can paste on glass only with water, you can fix it again if you fail.

We have attached Japanese special instructions for our company.

UV cutting, heat insulation, warmth

It can block harmful ultraviolet rays by 99% and is furniture friendly item.

Moreover, using a material with high insulation effect, the air layer (about 4 mm) of the seat blocks the outside air, and it improves the cold / heating efficiency.

Ultra thick type

After posting the protective sheet, the thickness after the post is 0.24 mm, it is thicker than ordinary electrostatic film, the pasting becomes easy, improving the strength of the glass.

Usage range

It is very applicable to blindfold decorations such as general glass windows, glass sliding doors, shower rooms and conference rooms.

Please note that the applicable film can only be used for glass)

Notes

It applies to smooth surface, it does not stick to coarse or uneven glass, it does not matter whether it is paired glass (double glass) or glass with glass or not, if the surface is flat (slippery), put it cleanly

I will.

Usage of window film:

1, Measure the size of the glass and cut the film.

2CM is held as an extra at the time of cutting, it is for future adjustment.

2, Peel off the protective film attached to the film.

3, Use a non-fluffy cloth to clean the glass.

4, wet the whole with a bubbling glass containing soap bubbles.

5, Remove air bubbles, water, etc. from the middle using credit cards and 尺.

6, Cut the excess part with the knife.

Notes

1, In the winter's cold season, the film may become stiff when it is rolled up, if you paste it, it may rise.

Please solve the problem by warming the film with a hair dryer before applying.

Or soak in hot water for a while. Paste it softens.

After that, even if it gets cold and solid, it will not rise.

2, Although it is recommended to paste in a size somewhat larger than the size of the glass and then cut off the remaining part with a cutter knife at the end

3, apply to smooth surface, do not paste on rough or uneven glass.

It is irrelevant whether it is a pair glass (double glass) or a glass with a mesh or structure, and if the surface is flat (slippery), it can be attached cleanly.

4, Be careful not to attach dust and fibers to the glass before pasting.

5, The surface to be stuck on the window is the surface from which the protective film has been peeled off (the surface slurping).

6, Please stick to the interior side.

7, Please peel off the protective film attached to the back of the film.

In case

8, When wetting with plenty of water, remove all of the air bubbles is a point that you can easily reuse.

(First of all, lightly spray the water on the film surface.This makes the squeegee easy to move.It is also important for scratch prevention.The basic is from top to bottom, from the center to the outside,

Crimp the film with squeegee and extrude the water in. Pull out the water with the kitchen paper so that the removed water will not return into the film.

Features:

• We only offer photographic specification films, Beautiful Life home products, packing notes of No. 7 According to the photographs, the label also comes with the film.
• Bright of Beautiful Life is being applied to 17 classes in Japan, Please note that for quality assurance, you will receive an order with 【Beautiful Life home products】.
• We have attached Japanese special instructions for our company.
• [Black · 100% opaque] Since it is black and completely opaque glass film, it becomes invisible from the outside after pasting.
• It protects the privacy properly, and it can cut the light firmly.
• 【Blindfold / Light Shielding】 With excellent light shielding property, indoor light does not leak out at all even at night.
• The pasted part is completely black and can completely block light, so the amount of light coming into the room is reduced and gentle.
• [UV cut · insulation · warmth] It is a gentle item that can block harmful ultraviolet rays by 99% and is furniture friendly.
• Moreover, using a material with high insulation effect, the air layer (about 4 mm) of the seat blocks the outside air, and it improves the cold / heating efficiency.
• 【Precautions】 Apply to smooth surface, do not stick to coarse or rough glasses, whether it is paired glass (double glass) or netted glass or not, regardless of whether the surface is flat (slippery)
• You can stick it neatly.
• [Security Assurance] If there is something about the product please do not hesitate to contact us, we will repeatedly ship, refund etc.

Product information:

Shipping Weight: 580 g

Package Dimensions: 4.19 x 4.19 x 91.59 cm