Description:The CC3D board is an all-in-one stabilization hardware which runs the OpenPilot? firmware. It can fly any airframe from fixed wing to an octocopter and is? configured and monitored using the OpenPilot Ground Control Station (GCS)? software.CopterControl from the OpenPilot project? introduces a new generation of multi-purpose aircraft stabilization platforms.The CC3D has been designed from the ground up to perform the following functions:- a MultiRotor controller with auto-level， including TriCopters， QuadCopters and? HexaCopters- a Flybarless Helicopter controller with auto-level- a Fixed Wing UAV controllerThe CopterControl hardware has the following features:Powerful STM32 32-bit microcontroller running at 90MIPs with 128KB Flash and? 20KB RAM3-axis high-performance MEMs gyros and 3-axis high-performance MEMs? accelerometerTiny 36mmx36mm 4 layer PCB for superior electrical noise reduction and flight? performance.Software support for Windows， Mac and LinuxDirect high speed USB support with no drivers required， a truly plug and play? device.Spektrum satellite receiver supportFutaba S-BUS hardware supportInnovative Flexi-port technology for superior port flexibility4Mbits on-board EEPROM for configuration storagePowerful STM32 32-bit microcontroller running at 90MIPs with 128KB Flash and 20KB RAM3-axis high-performance MEMs gyros and 3-axis high-performance MEMs accelerometerTiny 36mmx36mm 4 layer PCB for superior electrical noise reduction and flight performance.Software support for Windows， Mac and LinuxDirect high speed USB support with no drivers required， a truly plug and play device.Spektrum satellite receiver supportFutaba S-BUS hardware supportInnovative Flexi-port technology for superior port flexibility4Mbits on-board EEPROM for configuration storageFlexiportCopterControl also offers the innovative Flexi-port which provides either I2C connectivity or a second serial port. Flexi-port gives CopterControl the flexibility to use either I2C and a single serial port or dual serial ports， according to your connectivity needs.Superior user experienceOpenPilot has tried to make your experience with the CC3D as easy and trouble-free as possible. Naturally for a high-end product， the hardware is complete; there is nothing to solder. The included RC harness allows you to connect any standard PWM receiver. All CopterControl boards are tested before shipping and come with bootloader already flashed. A standard mini-USB cable (not included) is used to load the latest firmware and configure everything for your unique airframe.The OpenPilot project， whist still young， it trying to make Open Source much more user friendly. OpenPilot software is designed to be used by everybody! All major operating systems are supported and install packages are provided. The software is all Free software under the GPLv3 license and not only are you welcome to hack it， but we encourage it!Sensors and Components3-axis Gyroscope array and 3-axis Accelerometer: MPU-6000Supports several common RC inputs: 6 PWM channels， combined PPM， Spektrum/JR DSM2， DSMJ， DSMX satellites， and Futaba S.Bus receiversSimultaneous support for multiple receiversReceiverPort functions (configurable): 6 PWM input channels or combined PPM stream， 4 PWM output channelsMainPort functions (configurable): serial telemetry (default)， GPS， S.Bus， Spektrum/JR satellitesFlexiPort (configurable): serial telemetry， GPS， Spektrum/JR satellites， or I2C peripherals (under development)10 PWM outputs to servos or ESC¡¯s， or for camera stabilizationCamera stabilization: supports up to 3-axis camera mounts with stabilization and manual control from any of configured receiversOnboard USB connectivity for easy configurationUSB and serial telemetry and configuration (including wireless with optional radio modules)Supported by powerful OpenPilot GCS4 Mbit onboard memory3C Quaternion based complementary filter running at 500HzPackage size: 10 * 10 * 3 cm / 4 * 2 * 1.2 inPackage weight: 35 g / 1.2 ozPackage list:?????????????????????????????????????????????????? ?1 * Openpilot CC3D Open Source Flight Controller1 * 8pin cable2 * 4pin cable1 * Box?