range
value
test conditions
Positive voltage
Positive DC current about1.0mA?
Reverse voltage
3.0V
About 50맺
open-circuit voltage 1.0V
1.DC voltage?DCV?
| range | accuracy | Resolution |
| 600mV | ±(0.5%+5d) | 0.1mV |
| 6V | 1mV | |
| 60V | 10mV | |
| 600V | 100mV | |
| 1000V | ±(1.0%+6d) | 1V |
Input impedance:600mV>60M맺，10M맺
Overload protection? a)mV range DC current or 250V AC peak
b)1000V DC current or 750V AC peak
2. AC voltage
| range | accuracy | Resolution |
| 6V | ±(1.2%+5d) | 1mV |
| 60V | 10mV | |
| 600V | 100mV | |
| 750V | ±(1.5%+5d) | 1V |
Input impedance? 10M맺
Overload protection:a)mV range DC current or 250V AC peak
b)1000V DC current or 750V AC peak
Frequency response: 40 ~ 1000
Display: the average response (the effective value of sine wave calibration)
Duty display: (0.1%-99.9%)
3.DC current?DCA?
| range | accuracy | Resolution |
| 60uA | ±(0.8%+10d) | 0.01鈴A |
| 6mA | 1鈴A | |
| 60mA | 10鈴A | |
| 600mA | ±(1.2%+10d) | 100鈴A |
| 10A | ±(2.0%+10d) | 10mA |
Maximum input current?10A?No more than 15 seconds?
Overload protection?0.4A/250V recovery fuse
10A/500V fuse
4.AC current?ACA?
| range | accuracy | Resolution |
| 6mA | ±(1.0%+10d) | 1.0鈴A |
| 60mA | 10鈴A | |
| 600mA | ±(1.5%+10d) | 100鈴A |
| 10A | ±(2.5%+10d) | 10mA |
Maximum input current: 10 A(not more than 15 seconds).
Overload protection: 0.4 A / 250 recovery fuse;10A/500V fuse
Frequency response: 40 ~ 1000 Hz
Duty ratio : (0.1% ~99.9%)
5. Resistance?맺?
| range | accuracy | Resolution |
| 600맺 | ±(0.8%+10d) | 0.1맺 |
| 6k맺 | ±(0.8%+3d) | 1맺 |
| 60k맺 | 10맺 | |
| 600k맺 | 100맺 | |
| 6M맺 | 1k맺 | |
| 600M맺 | ±(1.2%+10d) | 100k맺 |
open-circuit voltage?about 1.0V?
Overload protection?250V DC current or AC current peak value
6. Diode and continuity Test
| range | value | test conditions |
|
| Positive voltage | Positive DC current about1.0mA? |
|
| About 50맺 | open-circuit voltage 1.0V |
Overload protection?250V DC current or AC current peak value
warning?For the sake of safety，donot input voltage range.
7. Capacitance
| range | accuracy | Resolution |
| 10nF | ±(4.0%+10d) | 0.001nF |
| 100nF | ±(3.0%+5d) | 0.01nF |
| 1鈴F | 0.1nF | |
| 10鈴F | 10nF | |
| 100鈴F | 10nF | |
| 6000鈴F | ±(5.0%+10d) | 100nF |
Overload protection?250V DC current or AC current peak value
Note?Below 100PF maybe cannot test
8.Frequency ?Hz%?
| range | accuracy | Resolution |
| 100Hz | ±(0.5%+3d) | 0.1Hz |
| 1000Hz | 1Hz | |
| 10kHz | 10Hz | |
| 100kHz | 100Hz | |
| 1MHz | 1kHz | |
| 10MHz | 10kHz |
sensitivity?2.0V
Overload protection? 250V DC current or AC current peak value
Duty ratio? (0.1%-99.9%)
range | accuracy | Resolution |
| 0.1%-99.9% | ±(0.5%+3d) | 0.1% |
9.Triode
| range | Display range | Test condition |
| HFE(NPN or PNP) | 0-1000 | Base current about 1mA VCE |
10.Temperature
| range | accuracy | Resolution |
| 0〕?300〕 | ±(1.0%+4d) | 1〕 |
| 301〕?1000〕 | ±(1.9%+5d) | 1〕 |
| 32팥?600팥 | ±(1.2%+6d) | 1팥 |
| 601팥?1832팥 | ±(1.9%+6d) | 1팥 |
Thermocouple? Kthermocouple
10. NCV
Set the function to NCV range and the meter display“EF” symbol. Put the meter close to the test object，when the object’s voltage is more than 110V(AC RMS) and the meter display “?”symbol，When sensing voltage is higher and shows more “?”symbol，the buzzer alarm sound the more densely populated.The red l ight is more bright.
