2G11 4-Pin 20W LED Lamp
(~5,400 lumens)
Replaces 40W/55W PL-L fluorescent lamp.

2G11 4-Pin 15W LED Lamp
(~2,160 lumens)
Replaces 36W PL-L fluorescent lamp.

2G11 4-Pin 10W LED Lamp
(~1,440 lumens)
Replaces 24W PL-L fluorescent lamp.





---ooo000ooo---



2G11 4-Pin 20W LED Lamp
Uses Standard 2835 (b) LED chips
LED Count: 90
Power Output: 20W (~5,400 lm)
Length: ~53 cm
Directly replaces a 40W/55W 2G11 PL-L fluorescent lamp


2G11 4-Pin 15W LED Lamp
Uses Standard 2835 (a) LED chips
LED Count: 90
Power Output: 15W (~2,160 lm)
Length: ~40 cm
Directly replaces a 36W 2G11 PL-L fluorescent lamp


2G11 4-Pin 10W LED Lamp
Uses Standard 2835 (a) LED chips
LED Count: 60
Power Output: 10W (~1,440 lm)
Length: ~32 cm
Directly replaces a 24W 2G11 PL-L fluorescent lamp



 Why 2835 LED Chips and Not 5050 Chips? 

LED Type

SMD2835

SMD5050

Led Dimension

2.8×3.5×0.8 mm

5.0×5.0×1.6 mm

Lumen

22-24 lm

16-18 lm

Color

R/G/B/W/Y

R/G/B/W/Y/RGB

Wire

Gold Wire

Metal Wire

Reliability

Good

Normal

Light Decline

Slow

Fast

Estimated Service Life of 3 years with a usage of 6 hours daily.
Dimmable and non-dimmable LED lamps have similar life span.

Can you use this LED lamp with an ordinary fluorescent lamp?
Yes!
Just make sure to bypass
the Ballast and the Starter
where the LED lamp is connected.
(See below for the procedure).

---ooo000ooo---


Daylight                Cool White           Warm White


in reverse order...



Daylight: in stock, 2-3 days delivery (weekdays)
Cool White: in stock, 2-3 days delivery (weekdays)
Warm White: in stock, 2-3 days delivery (weekdays)

---ooo000ooo---

INSTANT TURN ON!
No Flicker.
Minimum Heat.
Long-lasting.
Instant Savings. Long-term investment.

---ooo000ooo---

Dimmable
even without a dimmer.

First time turn on = 100% Brightness!
Turn off, wait for 2 seconds

Second time turn on = 50% Brightness!
Turn off, wait for 2 seconds

Third time turn on = 25% Brightness!

What Is The Savings On Electricity Then?
The values are approximate, but you will have an idea:
100% Brightness = 15W
50% Brightness = 7.5W
25% Brightness = 3.75W

---ooo000ooo---







---ooo000ooo---

To ensure proper operation,
LED Lamp must be connected
Without the BALLAST,
Without the STARTER

---ooo000ooo---

CAUTION:
Do not use or install this LED Lamp
with the ballast and/or the starter
still connected!
This will cause instant damage to the
LED Lamp.

Check out these steps on how to
bypass the ballast and starter connections.
For safety reasons, this procedure should be done
by a qualified or experienced personnel.

Basic Tools/Materials Needed:

1.  Ladder, 3 to 5 steps, depending on your ceiling height
2.  Screw Drivers, Big and Small, Standard (-) and Phillips (+)
3.  Side Cutter
4.  Long Nose Pliers
5.  End caps (included with each lamp)

 
This is the housing
showing the
original wiring.
A closer view
of the side
to be
worked on,
rewired.
The ballast
wiring
section.
The starter
wiring
section.
The original
36W lamp
side-by-side
with the
2G11 4-Pin
LED lamp.
Step 1:
Disconnect
ballast
wires.
Step 2:
Cut off
starter
housing
wires.
Strip about
5-8 mm
at the
wire ends.
Step 3:
Remove
starter
housing.
---
This step
is optional.
Step 4:
Remove
the
ballast.
---
This step
is optional.
Step 5:
Connect
wires
on
starter
side
using
an
end
cap.
(Clockwise
turn).

Continuation of the
procedure


Step 6:
Connect wires
on
ballast
side
using
an
end
cap.
(Clockwise
turn)
Step 7:
Make sure
that the
other side
is intact
for
testing
purposes.
This figure
shows the
completed
rewiring:

Starter
is bypassed
and
removed.

Ballast
is bypassed
and removed.
Check and
validate
Before this, fit up the
old 36W fluorescent lamp
on the other side and test it
to make sure
it works.
Step 8:
New 2G11
LED lamp
fitted in place.

  We're all done!   
Enjoy your new
LED lamp!

Instant turn on.
Flicker-free.
Economical.
Environment-
friendly!
Dimmable!





N.B.

If your lamp wiring is the same as Option 3 below, you have 2 possible steps to take:

1. Just remove the starter and do nothing more.
 - or -
2. Leave the starter connected; it is not used anyway.

Of course, #2 can lead to confusion that the starter is still in use. And you may think
that even the starter may need to be replaced when the LED lamp spoils.
I think #1 will be the best step to take: less work, no confusion.
Just hide the wires nice and safe so there is no hazard at all.

Thank you!




---ooo000ooo---




    Are you using an integrated ballast?    


Please refer to the following pictures
for the rewiring procedure.











---ooo000ooo---








If you've reached this point and have determined
that you need help, and don't know of anybody who can,
you may check out
Income Home Services

(No, we are not affialiated with them. Thank you!)




Remember...


2G11 4-Pin 20W LED Lamp
(~5,400 lumens)
Replaces 40W/55W PL-L fluorescent lamp.

2G11 4-Pin 15W LED Lamp
(~2,160 lumens)
Replaces 36W PL-L fluorescent lamp.

2G11 4-Pin 10W LED Lamp
(~1,440 lumens)
Replaces 24W PL-L fluorescent lamp.




---ooo000ooo---



2G11 4-Pin 20W LED Lamp
Uses Standard 2835 (b) LED chips
LED Count: 90
Power Output: 20W (~5,400 lm)
Length: ~53 cm
Directly replaces a 40W/55W 2G11 PL-L fluorescent lamp


2G11 4-Pin 15W LED Lamp
Uses Standard 2835 (a) LED chips
LED Count: 90
Power Output: 15W (~2,160 lm)
Length: ~40 cm
Directly replaces a 36W 2G11 PL-L fluorescent lamp


2G11 4-Pin 10W LED Lamp
Uses Standard 2835 (a) LED chips
LED Count: 60
Power Output: 10W (~1,440 lm)
Length: ~32 cm
Directly replaces a 24W 2G11 PL-L fluorescent lamp

---ooo000ooo---

INSTANT TURN ON!
No Flicker.
Minimum Heat.
Long-lasting.
Instant Savings. Long-term investment.

---ooo000ooo---

Dimmable
even without a dimmer.

First time turn on = 100% Brightness!
Turn off, wait for 2 seconds

Second time turn on = 50% Brightness!
Turn off, wait for 2 seconds

Third time turn on = 25% Brightness!

---ooo000ooo---






---ooo000ooo---


Daylight                Cool White           Warm White


in reverse order...


---ooo000ooo---



Warranty is 1 Year

Defect rate is known to be 20% (2 out of 10) within 18 months.
80% can last as long as 3 years.

So buying replacement lamps is already worth the cost.
(About $1 a month)



---ooo000ooo---

Bulk orders are very much welcome.

Questions?
Just drop us a mail at
pfrilzbestdeals[@]yahoo[.]com


We will do our best to answer your questions.
Thank you!