Introduction:
The remote trigger for studio flashes and outdoor flash is used as the controller of synchronous trigger studio flash of cameras. It consists of a signal sender and a receiver trigger and works by means of the frequency modulation wireless remote control.

The signal transmitter adopts the advanced circuit and components, and can transmit the coded FM wireless signa. The circuit of the transmitter has the function of standby and hibernation, thus it has low power consumption; the products can work under the standby mode for more than one year with only one battery; continuously trigger for thirty thousand times. the trigger current is only 0.01MA, which will definitely cause no damage to the flash contact of the camera. The transmitter is applicable to the traditional or digital camera with hot shoe or PC controlling interface.

Receiver trigger adopts dry battery for power supply, which is safe, energy-saving, and convenient. The product adopts micro-computer for controlling the decoding, Which has superior anti-interference capability; sensitive reaction speed, the highest synchronous speed can reach 1/250 sec.

All the models of the product uniquely have the multi-frequency isolation technique and the self coding matching function by users. Users can freely match and use the sender and the receiver according to the demands, which have 16 isolated channels to suit for specific shooting environments. Triggers set in different channels can be combined to work or independently work but do not interfere with each other in an efficient distance.

 

Specifications:

                                                    Transmitter      Receiver
 
Power Source                                      23A            AAA x2   

Outdoor operating distance                 >30M
(open area)
 
Indoor operating distance                  >10M
 
Frequency Channel                               4
 
Operating Frequency                        FM 433Mhz
 
Outdoor Synchronous Speed            (open area) Max 1/500sec

Indoor Synchronous Speed Max            1/250sec
 
How to use:

1.Make sure the channel selector of both transmitter and receiver at same position
2.Insert your flash hot shoe socket into the receiver's hot shoe jack 
3.Press the test button on your transmitter. The Flash should now flash 
4.Insert the transmitter's hot shoe socket into your camera's hot shoe jack 
5.(if your camera does not have a hot shoe use a PC sync cord and insert into the socket) 
6.You should now be ready to start shooting

 

Notice:This item doesn't support TTL mode.You need to change into M mode to operate!!

 

Suitable For:

for Nikon SB-900, SB-800, SB-600, SB-28, SB-27, SB-26, SB-25, SB-24;
for Canon 580EX II, 580EX, 550EX, 540EZ, 520EZ, 430EX/EXII, 430EZ, 420EX, 420EZ, 380EX; 
for Pentax AF-540 FGZ, AF-360 FGZ, AF-400 FT, AF-240 FT;
for Olympus FL-50, FL36;
for Sigma EF-500 DG Super, EF-500 DG ST, EF-430;
for Sunpak Auto 2000DZ, 622 Pro, 433AF, 433D, 383, 355AFm 344D, 333D;
for Vivitar 285HV (Older Vivitar 285/283 works only with PC sync);
Other flash models with a trigger voltage of 12V or lower;
Work with flash units using universal hot shoe like for Nikon, Sigma, Olympus, Pentax (except Minolta for SONY as they use a special hot shoe)

 

==========================================================

With 1 Receivers:

Package includes:

1PCSx Transmitter/Trigger

1PCSx PC Sync cord for camera (2.5mm to PC)

1PCSx PT-04 NE Receiver(with umbrella holder) 

 

 

==========================================================

With 2 Receivers:

Package Included:

1PCSx Transmitter/Trigger

1PCSx PC Sync cord for camera (2.5mm to PC)

2PCSx PT-04 NE Receiver(with umbrella holder)