Technical Specifications

1. 2.7" LCD Display Screen: TFT High-Definition Panel

2. Camera Lens: 5 mega-pixel， 140°ultra wide-angle lens and it is can be slightly adjustable

3. Video Resolution: WVGA / 720P/1080P

4. Video Recording Mode: Cycle Recording / Motion Detection

5. Video Format: AVI

6. Memory Card: TF Card/Micro SD (Maximum up to 32GB)

7. Sound Recording: Available

8. G-Sensor: Tri-axial Stereo Collision Acceleration Sensor

9. Video Signal: PAL/NTSC

10. Frequency: 50HZ/60HZ

11. Power Port: 5V

12. Battery: Built-in Polymer Lithium Cell

13. Built-in Bluetooth

14. Super Slim Mirror

Warranty 1 year due to factory defects.

Car Camera Feature Diagram

Description:

1. 2.7" Display Screen

2. Page Up

3. Page Down

4. Power On/Off/Menu (Double Click for more menu options)

5. Mode

6. OK

7. Phone Answer Key / Power On/Off

8. Bluetooth Indicator

9. On-Board Indicator

10. Speaker

11. Fastener

12. TV Out

13. Reset

14. USB Port

15. TF Card Slot /Micro SD(Support Micro SD Card max 32GB)

16. Camera (Angle Can be slightly adjustable)

Features !#!amp!*! Operations:

1. Installation: This digital video camera is easy to install. Just open the fastener and buckle it onto your rearview mirror， then connect the car charger to the cigarette lighter and the USB port to the camera. And the wires could be hidden in the car.

2. Charging: A. by connecting it to the on-board USB charger

B. by connecting it to the power cord: the camera automatically starts recording when the car is started， and it automatically turns off and saves the video file recorded when its power is cut off for 15 second.

(Note: Use only on-board power supply with an output of 5V/1A.)

3. Recording Mode: The camera automatically enters recording mode when you press (On/Off) or connect it to the on-board USB charger. (Please insert TF card first) and files are automatically saved to the TF card. The blue indicator light goes off when you unplug the on-board USB charger or press (On/Off) to turn the camera off.

4. Sound Recording

Sound recording is enabled by default. Press and hold ▲ for 2 seconds if you want to disable it .

5. Playback Mode

Press ▼ after video recording stops to enter playback mode. Press (▲ or ▼) to select the video recorded before or after and then press OK to play.

6. Protection Feature

Protection feature serves to protect and lock a certain video or all videos so that they won’t be recorded over during loop recording.

7. One-Key Lock

Press OK to lock the video being recorded so that it won’t be recorded over during loop recording. Press ▲ to unlock it and returns to loop recording mode.

8. Browsing through files to be deleted

Turn the camera on and press (Video Recording) to stop it from recording， then press ▼ to enter “Playback Mode”. Press ▲ (Page Up) to select the files recorded and press OK (Play) for preview. It you want a delete a certain file， press Key 4 (Menu) to enter “Delete Mode” when preview finishes. Press ▼ (Page Down) to select “Delete” or “Format”. Then continue by pressing (Menu) to exit.

9. Feature Setup

Turn the camera on and stop it from recording. Then press Key 4 (Menu) to enter “Setup Page”. Press ▼ to select specific parameters and press OK in the end to confirm your selection. When you are done with all the settings， press Key 4 (Menu) to exit “Setup page”.

Download Files:

1. Attached the USB cable to the computer directly to view the recorded files

2. By inserting the SD card to the computer to view the recorded files

Recording

1. Please put TF card in before you start with video recording.

2. Loop recording mode is available on this camera. When the TF card is full， the camera will delete the earliest videos recorded and save the latest ones recorded.

3. Please charge the camera with the on-board USB charger provided， which contains an adapter to convert the voltage from 12V/24V to 5V. The camera will be damaged if the output voltage is greater than 5V.

Bluetooth Features

You can set the Bluetooth on or off in the menu.

If it’s on， press and hold “Bluetooth” for two seconds to turn it off; if it’s already off you can turn it on in doing so.

Message behind the Icons:

1. Bluetooth Off: No icon.

2. indicates: Bluetooth on， but not connected to cell phone.

3. indicates: Bluetooth on and connected to cell phone.

Bluetooh Connection !#!amp!*! Pairing

1. In case that the rearview mirror Bluetooth is set to automatic start when the device is turned on and the cell phone in use used to pair up with the Bluetooth of the device， turn on the Bluetooth on both devices， and in the first 20 seconds after the rearview mirror Bluetooth is turned on， it will automatically search for the previous connected devices and assume default reconnection (indicated by a single flashing blue light). If the Bluetooth is on in more than one device that it previously paired up with， it will automatically choose the cell phone that it most recently paired up with.

2. If it fails to reconnect to the cell phone in 30 seconds， the rearview mirror Bluetooth automatically goes into stand-by mode (indicated by two alternating flashing blue lights on the device). You can now manually connect your cell phone to the mirror Bluetooth and pair them up.

3. Should pairing fail， the mirror Bluetooth switches to low power and stand-by mode.

4. If pairing is successful， the two blue lights on the mirror Bluetooth will go on and off at the same time. They both will be on when Bluetooth connection is successful but not functioning normally.

5. Both blue lights will be off when Bluetooth is working properly.

Note:

A. Please keep the cell phone less than one meter away from rearview mirror Bluetooth so that it’s easier for the former to detect the latter when the two are pairing up.

B. The name of the rearview mirror Bluetooth is “SJ900”.