WL580E – Wall-Plugged 300Mbps Dual Band Concurrent Wireless-N Repeater
Aztech WL580E is a Wall Plugged 300Mbps Dual Band Concurrent Wireless-N Range Repeater, which supports wireless 802.11a/b/g/n, and one 10/100Base-T Ethernet port.
The extender is equipped with 1 x 10/100M Auto MDI/MDIx LAN port that can be used to connect to an existing wired network to serve as a wireless interface. It can also be used to configure the extender via its web-based GUI, or upgrade the firmware.
The device is designed with MIMO technology, which successfully reduces 'blind spots', and extends network coverage within a home or in the building.
WL580E features with 64/128-bit WEP encryption and WIFI Protected Access (WPA), WPA2 to ensure the network security and prevent unauthorized access to you network.
The device is easy to setup. It is portable with no need of any external power adapter. It comes with the embedded power supply and power plug, so that users can just plug the device into a power socket.
Main Features:
- Dual-Band Concurrent 2x2 + 2x2 300Mbps Wireless Range Repeater
- Supports ratified 802.11n technology with the data transfer rate up to 300Mbps
- 2T2R for 802.11b/g/n for 2.4GHz band
- 802.11a/n for 5.0GHz band
- Repeats and extends existing wireless signal to areas where the router or access point is not able to reach
- Shares large files, printing and storage quickly and reliably in wider range in your home or office
- Eliminates the use of cable wires while providing reliable wireless connection
- Enables wired network wireless ready through the LAN port
- MIMO technology to reduce "blind spot" and increase network coverage
- WEP, WPA, and WPA2 to ensure network security from unauthorized access
- User-friendly web-based GUI and easy hardware setup Portable, no need of external power adapter
- Support WPS to both Router and Client devices
Hardware Specifications
| Wireless Standard Support |
- IEEE 802.11a/n 5.0GHz
- IEEE 802.11b/g/n 2.4GHz
- Ethernet IEEE 802.3 10/100, IEEE802.3u, IEEE802.3ab
|
| Wireless Frequency Band |
- 2412 MHz - 2484 MHz
- 5170 MHz – 5785 MHz
|
| Network Support |
- OFDM 1024/256/64/16/8 QAM, QPSK, BPSK and ROBO Modulation Scheme Wireless
- IEEE802.11n: BPSK, QPSK, QAM-16, QAM-64
- IEEE802.11g: BPSK, QPSK, QAM-16, QAM-64
- IEEE802.11b: CCK, QPSK, BPSK
|
| Security Support |
- Wireless: 64/128-bit WEP, WPA, WPA2
|
| Hardware |
- Key Chipset
- Mediatek MT7620A Network Processor + 2.4 GHz Wireless chip
- Mediatek RT5592EP 5GHz RF chip
- Memory
- SPI FlashRom : 8M Byte
- DDR2 DRAM : 64M Byte
|
| Platform Support |
- OS Independent with TCP/IP protocol installed
|
| Power Requirements (TBC) |
- Supply voltage range : 100VAC – 240VAC (50/60 Hz)
- Power Consumption : Less than 4W
- Max Current : 0.12A
|
|
Physical Specifications
| LED |
Color |
Behaviour |
| 1 |
Green |
- LED should be ON if WL580E is connected to Router and RSSI value is equal to HIGH
- LED should be OFF while WL580E is booting up
- LED should be OFF while WL580E is doing WPS authentication
|
| 2 |
Green |
- LED should be ON if WL580E is connected to Router and RSSI value is greater than or equal to MID
- LED should be OFF while WL580E is booting up
- LED should be OFF while WL580E is doing WPS authentication
|
| 3 |
Green |
- LED should be blinking if WL580E is NOT connected to any Router LED should be ON if WL580E is connected to Router and RSSI value is greater than or equal to LOW
- LED should be OFF while WL580E is booting up
- LED should be OFF while WL580E is doing WPS authentication
|
|
Yellow |
- LED should be ON during boot up. After fully bootup, LED will OFF
- LED should be blinking for 2 mins once WPS button is pressed
- LED should stop blinking and ON for 5 secs when WPS authentication is successful. Then LED should be OFF LED should be OFF
- if WL580E is connected to Router
|
| External Connectors |
- 1 x RJ45 : Fast Ethernet
- 1 x Factory Default Reset : Button
- 1 x WPS : Button
- 4 x Antennas : Internal Embedded
|
| Measurements |
- Dimensions : 105(L) x 58 (W) x 42 (H) mm
- Weight : 160 g
|
|
Regulatory Approvals
- USA : FCC
- Asia Pacific/ Europe : CE, CB
|
|
Environmental
| Temperature |
- Operting : 0° to 40° Celsius (32° to 104° Fahrenheit)
- Non-Operting : -25° to 70° Celsius (-13° to 158° Fahrenheit)
|
| Humidity |
- Operating : 30% to 90% Relative Humidity (Non-Condensing)
- Non-operating : 30% to 95% Relative Humidity (Non-Condensing)
|
|