The wireless doorbell includes one doorbell, one remote button and one battery

You can put batteries here

The popular compact linear design

• 1. Determine the preferred location for your receiver unit. The receiver unit contains the chime and is best located someplace central in your home. Most receiver units simply mount directly on an AC outlet using the attached plug
• 2. Install a new battery in the push button unit. You may need a flat head screwdriver to remove the cover of the unit. The screwdriver is normally inserted into a notch at either end of the unit. Use the screwdriver to gently pry the plastic cover away from the base
• 3. Test the door push button prior to mounting the push button unit. This assures you the chime unit is functioning and allows you to gauge the volume at the selected location
• 4. Adjust the transmitter frequency from the push button if the chime in the receiver unit does not sound. Remove the cover as described in Step 2 and locate the frequency settings
• 5. Make additional adjustments, depending on your specific model, for volume and chime ring tone. Most models feature adjustable ring tones so you can discern which door´s push button has been activated. These adjustments are made by removing the cover of the receiver unit. Adjust the chime volume and ring tone frequencies according to the labeled settings
• 6. Mount the push button unit, or units, beside the desired doors. Some units have holes in the base for mounting screws. If so, you will need to remove the cover and use your screwdriver to drive the screws into the wall. Other units use a strong adhesive strip that allows for quick and easy mounting to vinyl or metal surfaces

• 1. Batteries
• 2. Screwdrivers
• 3. Wood shims (if necessary)
• 4. Needle-nose pliers

• 1. Open up the cover on both the wireless doorbell button device and the chime. Depending on your model, you may have to remove a small screw or two to do this or the cover may be pried off with a screwdriver
• 2. Replace the batteries in each device with a fresh set. If the wireless doorbell was working previously, then dead batteries are usually the cause of one that is not working now
• 3. Check the frequency indicator on both the button and the chime. They should both be set to the exact same frequency. The frequency is set by a series of jumpers, usually located near the battery. If there is a difference between the two devices, move the jumpers on one or the other so that they both are set identical. Using needle-nose pliers will make it easier to change the jumper settings. Put the covers back on and test the wireless doorbell. If it still is not working, continue to the next step
• 4. Remove the wireless doorbell chime from the wall and try placing it in a location that is closer to the doorbell button. If the wireless doorbell chime works when it is removed from the wall, it may be because it was secured to metal studs. Metal studs can interfere with the transmitted signal. This can be rectified by installing wood shims between the chime and the metal studs
• 5. Make sure that your doorbell chime is installed higher up on the wall. If you have a concrete floor and the chime is installed too close to the floor, the transmitted signal will be weakened. Position your chime at different areas on the wall to ensure that it receives a quality signal every time you press the doorbell

If over time the door chime fails to sound, or sounds intermittently, check the battery in the push button unit and make sure the receiver unit is still plugged into the wall outlet

FEATURES

• Blue Flash light on when guest pressing the remote button
• You can install the doorbells in locations, such as kitchen, back yard, bedroom, etc. never miss the guest
• Completely wireless operation - no wires or cables required
• Up-date intelligent flash light design brings convenience to the hearing handicapped
• Wireless easy mounting design never affects your inner decoration and makes the doorbell anywhere you like
• All day long anti-interference system, pretends the doorbell from interferences outside or between neighbors
• Delicate smart part, makes the doorbell a saluting angel of dwelling house, woke building, hotel, factory and so on. You never miss any guest

Specifications

Package Includes

• 1 x Home Security Wireless LED Flashing Doorbell (Three Kinds of DC Supply)
• 1 x Doorbell Switch
• 1 x 23A 12V Battery