Products

Car multi-functional emergency warning lights is a new automotive products， the product-free wiring， maintenance-free， the product inside the solar charging module and lithium battery storage devices， warning function automatically open the lights while driving at night to have a good road safety supporting role.

Features:

1. solar charging， lithium power storage， free wiring， maintenance-free， efficient and environmentally friendly;

2. Product shell injection molding， the opening position of high-performance silicone potting， corrosion， anti-aging， waterproof performance is extremely good， it can be avoided due to high pressure water washing the body and cause damage to the product.

3. Intelligent control system， built-in high sensitivity vibration sensor and photographic system， while under low light conditions flicker in the road on their own. And there is a delay-off feature automatically turns off to work in the process of parking and red light， parking or body no vibration 120 seconds after;

The driver of the car care function， after the car near the range of 10 meters， multifunction warning light will automatically stop light， or the distance from the car after overtaking warning light starts flashing again.

5. The latest inductive switch， built-in multi flashing pattern of self-regulation.

Product Features:

Theft， traffic warning， rear-end features， products built-in high sensitivity vibration sensor， a slight touch of the body at night criminals， product warning function automatically open light can cause the attention of passers， play a role in intimidating criminals. Product highlight RGB LED lights， built a variety of flashing mode， pasted on the car fog position， driving at night to remind oncoming vehicle， the rear of the vehicle can also be a warning to prevent rear-end accidents.

Product installation:

Warning lights affixed to car fog position to be pasted on the front car， rear bumper or car fixation position in the network license.

 

Use Method

8 lights / 16 light Magnetron paragraph

Products using the smart control system， built-in high sensitivity vibration sensor and photographic system， while under low light conditions automatically flash in the road. And there is a delay-off feature automatically turns off to work in the process of parking and red light， parking or body no vibration 120 seconds after;

Warning lights built-in sensor switch， control diskette area near the magnetron 3 seconds to turn off warning lights， close the control over the magnetic floppy zone warning lights can be opened again. After the warning lights turn on， remove the floppy and close to 1 second after flashing mode can be changed again.

16 lights can be remote control car models

16 LED warning lights remote control models using dual smart chip， the product in the original sense of intelligent dual (ambient light and vehicle vibration intensity) on the basis， in addition equipped with a self-learning type remote receiver unit can control the lights in the car to open close， mode switching， flashing frequency conversion functions.

The remote control uses:

Open light: Press the A button for 2 seconds， at the same time as the red light flashes three times to open the reminder

Turn off the lights: Press the C key for 2 seconds to turn off

Transform light mode: Click the B button once can alter one light mode， built-in 13 kinds of modes can be selected

Transform flicker frequency: Tap C key one can alter one light frequency， products are slow Strobe - Fast Strobe - Strobe - Breath - Solid 5 frequencies can be selected

Failure mode starts: Click the A button once， green light flashes three tips， then light sensor and vehicle vibration sensor is invalid， regardless of the day or night lamp remains current state of work until the battery runs out

 

Normal mode is activated: Click the A button once， blue lights flashing three tips， this time sensing and vehicle vibration sensor effective only at night to drive to light， low light or no vibration lights are not bright

Remote Reset: Press the D button for 2 seconds， the remote control can be reset， while white light flashes three times as a reminder， do not use this feature.

Note: When using light conversion function， flicker frequency conversion function， failure mode and normal mode switching function when asked to press A key for 2 seconds to activate the remote control receiver， after receiving the device will have two minutes to start ， 2 After receiving apparatus minute wait to re-enter active.

Remote reset mode: factory set to a remote control can only control a warning light， if you want a remote control simultaneously control multiple warning lights， first press the remote control Original D button for 2 seconds， then the white light flashes three times， enter the reset state， and then press any one remote A button for 2 seconds， see red warning light flashes three times， it means that the reset is complete. Such as setting a remote control can control five warning lights， then followed by pressing the D key original equipment remote control for 2 seconds， then press any one of the remote A button for 2 seconds， so you can five warning lights while receiving a remote control， the other four invalid wife， if you want to return to the original one in a controlled manner， using the inverse steps to return!

Remote control distance: 5-10 meters， open area without interference up to 20 meters

Remote control receiver antenna: Remote receiving antenna attached in the proper location.

Special Note: warning lamp power is low when the remote control will be unresponsive goods or invalid!