The charger can only charge a length not longer than 70mm of 3.7V lithium battery
Test Capacity: The first discharge to 2.75V， recharge， charge to stop showing after 4.2V capacity is the actual capacity of the battery.

Test Resistance: charger plugged in after the battery into the charging slot display prompts to enter the charging current selection， press the key to select 500mAH this file， choose Fixed gear after 8 seconds into the state of charge， and then press the key three times can see the battery resistance， please note that this test out the internal resistance than the more specialized instruments measured about 10 milliohms， within the actual resistance measured internal resistance -10 =
    A warning
    1.1 This charger can only charge a cylindrical lithium ion battery;
    1.2 Before use， please refer to the instructions carefully， pay attention to the recommendation of the rechargeable battery charging current， do not exceed the recommended charging current;
    1.3 Do not use other power adapter;
    1.4 Chargers discharge may be hot， be careful not to burn;
    1.5 stop using， unplug the power;
    1.6 can be used in normal room.

    Second， characteristics
    2.1 two charging current regulator (500mA / 1000mA);
    2.2 can be of different size (18650/26650) at the same time charging the battery;
    2.3 Each has a separate LCD display battery charging parameters;
    Under 2.4 Charger mode， different charging current charging;
    2.5 Dischareger mode (first discharging and then fully charge)， detection of battery capacity;
    2.6Charger and Dischareger two modes can be performed simultaneously;
    2.7 Each battery can be charged simultaneously or independently set / capacitance sensing function;
    Over 2.8 kinds of display modes， current (mA) / capacity (mAh) / voltage (V) / Time (h) / resistance (mR of);
    2.9 with a dedicated power adapter.



    Third， the key (MODE) is described
    3.1 charger has two buttons， each control all the way， using a simple and convenient;
    3.2 In any case hold the MODE button for 3 seconds to change Charger (charging) mode or Discharege (capacity test) mode， and then press the light again within 8 seconds to change the current selected current 8 seconds to enter the work state， in working condition can tap the (MODE) key to view the current (mA) / capacity (mAh) / voltage (V) / time (h) / resistance (mR).



    Fourth， the operating mode
    4.1 Charge Mode (charging mode)
    4.1.1 When the charger is powered on， all LCD screens charger instant full light if the battery is not placed will display Null， if it is a bad battery will also be displayed into the Null;
    4.1.2 When the charger into the battery charger in three seconds or so to measure the internal resistance of the battery， then the system automatically enters the charging current selection mode， the screen with the words "500mA" flashing 8 seconds， during through mode key to select the current 500mA or 1000 mA charging system is locked in 8 seconds after you select the charging current， if within 8 seconds， did not make the set， then the system automatically 500mA charging current， then the current Unable to change， to change the battery needs to be reset;
    4.1.3 Users should pay attention to the large rechargeable battery charging current if rapid charging is not required， it is recommended charging 500mA， this battery is safe and is also advantageous;
    4.1.4 under charging mode by tapping the mode button to switch to view the charge capacity (mAh) / charging time (h) / battery internal resistance (mR) / charging current (mA)， 4 kinds of units， after the battery is fully charged， the display Full， the next row of small print displays charge end (end of charge);

    4.2 Discharge Mode (capacity detection mode)
    4.2.1 Discharge Mode is the first battery is full， then the battery discharge capacity to detect and record the discharge capacity of the battery after the battery is full automatic;

    4.2.2 - the battery into the charger measure the internal resistance of the battery， in any mode， press mode button for 3 seconds to enter the Discharge mode; Discharge
    - After entering Discharge mode， the screen appear the words "500mA" flashing 8 seconds， during through mode button to select 500mA or 1000 mA current， the current system locks you selected in 8 seconds after， if it within 8 seconds ， did not make the set， then the system will automatically lock 500mA current to charge the battery (the selected current is the current system to charge the battery);
    - When the battery is full， the system automatically to 500mA current to the battery discharge capacity and discharge records， to detect the battery capacity， when the screen appears Discharher and when the capacity test mode is finished， the screen flashes the actual capacity at this time is the battery power parameters ;.
    - After the capacity test mode is finished， the charger will again before the selected parameter current to charge the battery until it is full.

    V. Specific Parameters
    5.1 DC Input voltage: 12V / 1.5A
    5.2 Li-ion battery charging current: 2X (4.2V 500mA)， 2X (4.2V 1000mA)
    5.3 Rechargeable Battery: 18650，26650， etc.
    5.4 Termination: Intelligent voltage monitoring
    5.5 Dimensions: 132mm (length) * 65mm (width) * 31mm (height) a warning
    1.1 This charger can only charge a cylindrical lithium ion battery;
    1.2 Before use， please refer to the instructions carefully， pay attention to the recommendation of the rechargeable battery charging current， do not exceed the recommended charging current;
    1.3 Do not use other power adapter;
    1.4 Chargers discharge may be hot， be careful not to burn;
    1.5 stop using， unplug the power;
    1.6 can be used in normal room.

    Second， characteristics
    2.1 two charging current regulator (500mA / 1000mA);
    2.2 can be of different size (18650/26650) at the same time charging the battery;
    2.3 Each has a separate LCD display battery charging parameters;
    Under 2.4 Charger mode， different charging current charging;
    2.5 Dischareger mode (first discharging and then fully charge)， detection of battery capacity;
    2.6Charger and Dischareger two modes can be performed simultaneously;
    2.7 Each battery can be charged simultaneously or independently set / capacitance sensing function;
    Over 2.8 kinds of display modes， current (mA) / capacity (mAh) / voltage (V) / Time (h) / resistance (mR of);
    2.9 with a dedicated power adapter.



    Third， the key (MODE) is described
    3.1 charger has two buttons， each control all the way， using a simple and convenient;
    3.2 In any case hold the MODE button for 3 seconds to change Charger (charging) mode or Discharege (capacity test) mode， and then press the light again within 8 seconds to change the current selected current 8 seconds to enter the work state， in working condition can tap the (MODE) key to view the current (mA) / capacity (mAh) / voltage (V) / time (h) / resistance (mR).



    Fourth， the operating mode
    4.1 Charge Mode (charging mode)
    4.1.1 When the charger is powered on， all LCD screens charger instant full light if the battery is not placed will display Null， if it is a bad battery will also be displayed into the Null;
    4.1.2 When the charger into the battery charger in three seconds or so to measure the internal resistance of the battery， then the system automatically enters the charging current selection mode， the screen with the words "500mA" flashing 8 seconds， during through mode key to select the current 500mA or 1000 mA charging system is locked in 8 seconds after you select the charging current， if within 8 seconds， did not make the set， then the system automatically 500mA charging current， then the current Unable to change， to change the battery needs to be reset;
    4.1.3 Users should pay attention to the large rechargeable battery charging current if rapid charging is not required， it is recommended charging 500mA， this battery is safe and is also advantageous;
    4.1.4 under charging mode by tapping the mode button to switch to view the charge capacity (mAh) / charging time (h) / battery internal resistance (mR) / charging current (mA)， 4 kinds of units， after the battery is fully charged， the display Full， the next row of small print displays charge end (end of charge);

    4.2 Discharge Mode (capacity detection mode)
    4.2.1 Discharge Mode is the first battery is full， then the battery discharge capacity to detect and record the discharge capacity of the battery after the battery is full automatic;

    4.2.2 - the battery into the charger measure the internal resistance of the battery， in any mode， press mode button for 3 seconds to enter the Discharge mode; Discharge
    - After entering Discharge mode， the screen appear the words "500mA" flashing 8 seconds， during through mode button to select 500mA or 1000 mA current， the current system locks you selected in 8 seconds after， if it within 8 seconds ， did not make the set， then the system will automatically lock 500mA current to charge the battery (the selected current is the current system to charge the battery);
    - When the battery is full， the system automatically to 500mA current to the battery discharge capacity and discharge records， to detect the battery capacity， when the screen appears Discharher and when the capacity test mode is finished， the screen flashes the actual capacity at this time is the battery power parameters ;.
    - After the capacity test mode is finished， the charger will again before the selected parameter current to charge the battery until it is full.

    V. Specific Parameters
    5.1 DC Input voltage: 12V / 1.5A
    5.2 Li-ion battery charging current: 2X (4.2V 500mA)， 2X (4.2V 1000mA)
    5.3 Rechargeable Battery: 18650，26650， etc.
    5.4 Termination: Intelligent voltage monitoring
    5.5 Dimensions: 132mm (length) * 65mm (width) * 31mm (height)

LiitoKala Lii-260，它是一款高端智能充电器，具有双通道独立充电/电池容量检测/电池内阻检测/防反接/短路保护/过流保护及电池零伏激活等七大功能，同时能自动适时地监控电池的电压。