Item Descriptions:

By installing the waterproof smartphone bar mount holder, you can enjoy the smartphone function comfortably.

Smartphone Holder Bar Mount Waterproof 360 degrees can be rotated.

Waterproof specification (not waterproof), which protect smartphones and others from sudden rain.

Motorbike bike You can attach it to a bar handle such as a bicycle.

Touch screen operation is possible with the smartphone in the case.

* Compatible models: iPhone 6 6s 7 Plus can be installed, of course, but please note that tablet terminals such as Nexus Galaxy xperia must check the size and case size before purchasing.

Easy installation on the bar handle is possible.

The main body can rotate 360 ​​degrees.

Since the ball joint is mounted on the mount, it can be adjusted to an angle that is easy to see up, down, left and right.

Case outer dimensions: length of about 16.5 cm X width 10.5 cm X height 3 cm inside dimension: length of about 14.5 cm X width 7.7 cm X height 2 cm (iPhone 6 Plus can be installed) Bar mount mountable diameter about 20 - 33 mm Open end for installation

(Spanner) 10 mm tool required, please be prepared by customer.

Depending on the size of the smartphone, there are cases where installation is impossible so please purchase after confirming well before purchasing.

Accessories: Urethane spacer for internal height adjustment 2 pieces 3 mm + 10 mm each 1 piece Splining prevention spring strap 1 piece (Please devise and use it for fall prevention etc.) With simple instruction manual

Protects the smartphone from sudden rain, waterproof specification (not waterproof)

When navi or smartphone is put in the case, urethane spacer for height adjustment is attached to each 3 mm and 10 mm each for close contact with the case surface to improve operability.

In case

The case can rotate 360 ​​degrees.

In case

Although tools are necessary, it is easy to install.

In case

Mounting method

【installation method】

1.

Please attach the holder to the bar mount.

In case

As the measures to prevent the mounts and holders from falling off due to vibrations or the like, the fittings are getting stiff, so after setting the mount and the holder, put more force and push it in to fix it.

In case

2.

Please adjust the angle with the bar mount and the holder.

In case

3.

Please attach the bar mount to the handle etc.

In case

Please be sure to check your dimensions of navigation and smartphone before purchasing.

In case

Although the transparent vinyl part of the case is somewhat, it may be wavy.

In case

Since the transparent vinyl of the case is a thick material, the reaction of touch operation may be bad.

In case

Image smartphone etc .. is not attached.

In case

Size

【Size】

Case outer dimensions: length of about 16.5 cm X width 10.5 cm X height 3 cm inside dimension: length of about 14.5 cm X width 7.7 cm X height 2 cm (iPhone 6 Plus installable)

Bar mount mountable diameter about 20 - 33 mm

For installation, open end (spanner) 10 mm tool is required, please be prepared by customer.

This product is not a product that guarantees sufficient fixation.

In case

Those who wish to fix sufficiently please fix screws, bonds, rubber etc. Please prepare.

In case

Because it is not heat resistant specification, there is a possibility of dropout of the mounted item depending on the usage situation.

Avoid using it in a place exposed to direct sunlight.

It may cause cracks, warping, etc.

Features:

• Smartphone Holder Bar Mount Waterproof 360 degrees can be rotated.
• Waterproof specification (not waterproof) that protects smartphones and others from sudden rain.
• Motorbike bike You can attach it to a bar handle such as a bicycle.
• Touch screen operation is possible with the smartphone in the case.
• ※ Applicable model: iPhone 8 8plus X 7 7s 7plus 6 6s 6plus can be installed, of course, please purchase tablet terminals such as Nexus Galaxy xperia after checking the size and case size.
• Easy installation on the bar handle is possible.
• The main body can rotate 360 ​​degrees.
• Since the ball joint is mounted on the mount, it can be adjusted to an angle that is easy to see up, down, left and right.
• Case outer dimensions: length of about 16.5 cm X width 10.5 cm X height 3 cm inside dimension: length of about 14.5 cm X width 7.7 cm X height 2 cm (iPhone 6 Plus can be installed) Bar mount mountable diameter about 20 - 33 mm Open end for installation
• (Spanner) A tool of 10 mm is required, please prepare by customer.
• Depending on the size of the smartphone, there are cases where installation is impossible so please purchase after confirming well before purchasing.
• Accessories: Urethane spacer for internal height adjustment 2 pieces 3 mm + 10 mm each 1 piece Splining prevention spring strap 1 piece (Please devise and use it for fall prevention etc.) With simple instruction manual

Product information:

Shipping Weight: 199 g

Package Dimensions: 4.19 x 15.39 x 16.61 cm