Item Descriptions:

size:

iPhone 6s & 6 (4.7)

| Color:

SpaceGray

(IMPORTANT) Be sure to conduct a waterproof test before installing iPhone

Peel off from the bottom right recess

Please soak for about 10 minutes

The front screen of the zip type will peel off when you roll from the recess in the front right lower side.

(The back side can be peeled as well)

Please check that it is sealed with chitin such as screen zip and earphone port, and soak in cup and so on for about 10 minutes in a container filled with water.

Please insert the iPhone after checking whether water drops are intruding inside after 10 minutes.

* Sealing is insufficient when flooded.

Make sure that foreign matter is caught in the groove (aluminum side) of the zip and earphone / charge port seal is not disengaged.

In case

(IMPORTANT) Please properly attach the manner switch when installing it

Lever type

Dial type

When setting the iPhone please set from the upper left front to set the manner switch on the volume switch accurately.

* There are two kinds of manner switches on 4.7 inches.

It is almost dial type but can not be selected.

Please acknowledge it beforehand

Lever type (image left)

Please properly put a manner switch between the two pins.

Manner ON / OFF converts the rotation of the lever to upper and lower of the manner switch with two pins (see the figure).

There are two pins under the translucent protective sheet (Please do not peel off).

Please rotate the lever to understand how the pin moves and insert a manner switch between the two pins.

If it is not set correctly it will not work properly.

If you operate with inappropriate set, the dial side will be damaged due to switch protection of iPhone.

be careful

Dial type (image right)

Switch the manner mode by rotating the dial.

Switching ON / OFF switches with rotation of several millimeters.

If it is rotated too much or in the reverse direction, the dial side will be damaged due to switch protection of the iPhone

.

be careful

[Important] Please set the screen jig correctly.

Slide your finger and snap it around

When installed

After placing the iPhone in the case, fit the front screen zip to the aluminum frame.

Instead of fitting in several places at this time, I slide the belly of the finger and put it all around.

Please check whether any foreign matter is caught in the groove of the aluminum frame.

If rubber is waving after installation, please refit from the beginning as inset is insufficient.

In case

When removing the iPhone

After removing the screen of the front side, you can easily take out by peeling off part of the screen on the back side and pushing out from the back side.

* This product is not intended to use tempered glass etc.

Because it will damage the effective space of sensitivity reduction and shock absorption, please use it at your own risk when used together.

Other accessories are similar.

* This product is

It is compatible with Apple's original lightning cable.

You can not use cables with a large connector size for external products

.

(MFI certification cable is also bigger than the one manufactured by Apple) Also earphone plug hole can not be installed as it is with outside diameter thick plug with diameter adjusted to Apple genuine.

Please note in advance

* For the first time purchasing a waterproof case

Although it can say to the waterproof case in general, a filter is attached to the microphone / speaker to prevent the invasion of water.

Although there is a degree difference between manufacturers, the quality of the call will definitely lower than the state without a case attached.

Although this product is relatively good, there is still no waterproof case that the call quality does not change at all.

Please purchase after understanding / as a disadvantage.

Features:

• Please enter model number Confirm this is compatible:
• * This product is compatible with Apple's original lightning cable.
• Cables with a large connector size for external products can not be used.
• (MFI certification cable is also bigger than the one manufactured by Apple) Also earphone plug hole can not be installed as it is with outside diameter thick plug with diameter adjusted to Apple genuine.
• Please be careful in advance * For the first time to buy a waterproof case you can say to the waterproof case in general, but a filter is attached to the microphone / speaker to prevent water intrusion.
• Although there is a degree difference between manufacturers, the quality of the call will definitely lower than the state without a case attached.
• Although this product is relatively good, there is still no waterproof case that the call quality does not change at all.
• Please purchase after understanding / as a disadvantage.
• IP68 Waterproof / Snowfree / Dustproof Case with Aluminum Material for Mainframe Unique Zip System Easy to Removable
• Screen part improves scratch resistance.
• Touch ID operation possible with the case attached
• Impact resistance protects the terminal from drop shock of 2 m Dimension: 148 x 80 x 11.2 (mm) Weight 51 (g)
• Dimple with excellent holdability is installed at 4 rear positions.
• With floaters attachable strap hole

Product information:

Shipping Weight: 104 g

Package Dimensions: 2.29 x 10.16 x 22.35 cm