■在庫はない場合は、通常5～10日以内に発送。販売元直送の場合もあります、発送後に追跡番号を発行。 納品日数は最大10-15日の場合もあります。<br/>■初期不良・不良品による返品・交換(3日内)の返品送料はお客様負担となります。<br/>Holybro Kakute F4 AIO V2 Flight Controller PDB OSD+Atlatl HV 5.8G 40CH Raceband FPV Transmitter for RC Drone<br/><br/><br/>Holybro Kakute F4 AIO V2 Flight Controller PDB OSD+Holybro Atlatl HV 5.8G 40CH Raceband FPV Transmitter ? ? ? ? ?<br/><br/><br/><br/><br/><br/><br/><br/>Holybro Kakute F4 AIO V2(user munual):<br/>Brand name: Holybro?<br/>Item name: F4 AIO V2 Flight Controller<br/>MCU: STM32F405RGT6 32-bit processor<br/>IMU: ICM20689 (SPI)<br/>Barometer: BMP280<br/>USB VCP Driver (all UARTs usable simultaneously; USB does not take up a UART)<br/>5 hardware UARTS (UART1  3  4  5  6)<br/>Supports serial receivers (SBUS  iBus  Spektrum  Crossfire) only. PPM and PWM receivers are not supported.<br/>128 Mbit Dataflash chip for Blackbox logging<br/>Dimensions: 35x43x7mm (includes USB in height)<br/>Mounting Holes: Standard 30.5mm square to center of holes?<br/>Weight: 7g<br/>?<br/>Features:<br/>-Additional UART (UART 4) added to support serial camera communication such as to RunCam Split. Please note this is NOT the same as Betaflight Camera Control feature  which controls the menu of FPV cameras like Swift  Monster  etc.<br/>-Additional UART (UART 5) added to support ESC telemetry such as from BLHeli_32 and KISS.<br/>-Through-hole solder pads instead of flat pads for more secure soldering especially for beginners.<br/>-Barometer sensor on board allows altitude hold mode.<br/>-I2C pad available for certain external sensors.<br/>-Supports Betaflight and Cleanflight.<br/>-Betaflight OSD. Change PIDs  adjust common configuration parameters  and change video transmitter channel and power level  all using your transmitter sticks and goggles.<br/>-Soft-mounting built in. The IMU (“gyro”) chip on this board is mounted on vibration-isolating foam. This means that there is no need to soft-mount the board itself.<br/>-New high-performance / low-noise / high sensitivity IMU. ICM20689 with 6-axis gyro and accelerometer. Can run at up to 32 kHz.<br/>-2 oz. copper PCB allows up to 120A maximum continuous current.<br/>-Dedicated bootloader button for easy firmware flashing.<br/>-Low-profile design fits into even very compact frames.<br/>-Input voltage 7v to 42v. Power the board directly from the flight pack  up to 6S (on “B+” pad only).<br/>-Automatic voltage monitoring. No need to run a separate vBat wire for voltage monitoring; the Kakute F4 AIO monitors voltage directly from the battery power lead.<br/>-Filtered voltage output for clean  noise-free video. On-board regulators output 5v at up to 1.5 amps and 3.3v at up to 200 mA to power peripherals such as receiver  video transmitter  FPV camera  or LED strip.<br/>-Supports BLHeli pass-through for easy ESC upgrade and configuration.<br/><br/>?Atlatl HV specification(user manual):<br/>Item Name: 5.8G 40CH?15/25/100/200/400/600mW FPV Transmitter<br/>Model:??Atlatl HV<br/>Transmitting Output Power:?15mW ( Pit Mode)<br/>? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ??25mW/ 100mW/ 200mW/ 400mW/ 600mW Switchable<br/>Audio: ?6 MHz + 6.5 MHz Mono<br/>Antenna Connector: MMCX<br/>Input Voltage: 7-24V (2-6S Lipo)<br/>Dimension: 35(L)x 35(W)x 7(H)mm?<br/>Mounting Hole: 30.5x30.5mm<br/>Weight: 10.8g<br/><br/>Features:<br/>-Compatible with all major FPV receivers from vendors such as Fatshark  ImmersionRC  etc.<br/>-Supports the standard 40-channel set: band A  B  E  Fatshark  and Raceband.<br/>-Telemetry input allows remote control by the flight controller (where supported). Change channel  transmit power  and more from Betaflight OSD  flight controller USB port  ?Taranis  and more.<br/>-Variable transmit power from 25 mW to 600 mW. Use 25 mW for a race and then easily switch to 600 mW for freestyle.<br/>-Pit Mode allows you to power up safely without the risk of knocking other pilots out of the air.<br/>-Mono audio input allows you to install a microphone  so you can listen to your motors while you fly  no matter how far away you fly.<br/>-Standard 36mm form factor allows you to mount the Atlatl directly in your flight controller stack.<br/><br/>Package included:<br/>1* Kakute?f4 AIO V2+Atlatl stack<br/>1* Heat sink<br/>1* 80mm SMA--MMCX Cable<br/>1* 150mm 4pin JST GH wire