Item Descriptions:

size:

75 x 140 cm

Product introduction

lightweight

Shutter type bath lid

It is light-weighted for the elderly and children

Dirt is difficult to attach, easy to clean

From Amazon

lightweight

Bath lid which is gentle to seniors and ladies Compared with conventional salt resin

Approximately 30% lighter (compared to PVC made by Pearl Metal Company)

Dirt hardly attached and easy to clean

Product Safety Association Certified SG Approved

SG mark system is a guarantee system against injuries caused by the loss of the bathtub lid

Environment-friendly polystyrene that does not generate dioxin and other substances upon incineration (all materials)

You can cut DIY freely according to the place

Optional "

DIY cap for repair 20 pieces HB-905

By using "

Processing of deformation etc. can be done by myself

In the bath tub of the house there is a drain plug etc. In the existing shutter lid

When it does not become exact, cut the lid and be attached to the cut face

As for the cap, there are plane and step oblique processing (left and right 45 degrees)

Processing method

【Required Equipment】

Plastic saws: As low as possible blade height and finer ones (yarn saw etc.)

File: Used as finish of cut surface

Marking pen: used to draw a line on a lid

General adhesive for plastics (may be instant adhesives)

Cutter (if necessary)

DIY cap: Close after side processing

DIY cap for repair 20 pieces HB-905 is here >>

【Processing method】

1. On the concave processing width side

(1) Copy it from the paper pattern to the shutter cover (hereinafter referred to as the lid) and cut it

(2) to arrange with the file when cutting it

2. On the concave processing length side

(Attention: two or more mountains)

(1) Copy it to the lid from the paper pattern

(2) Check the place to cut, fold the lid in half and cut a part

(3) When cutting, the soft part (the rubber part between the mountain and the mountain) is still attached

So, remove the soft part with a cutter etc.

(4) Cut the remaining necessary cut part

(5) Fix the cutting place with a file

3. Stair diagonal processing

(1) Copy it to the lid from the paper pattern and cut it

* When cutting, please cut from the outside (width side)

(2) Fix the cutting place with a file

Apply adhesive to cap and attach

※ Please curing for a while until it gets dry (leave it to a well ventilated place)

Attention: How to measure bathtub size

【How to measure bathtub size】

Please measure the size near the center of the opposite end from the end of the bathtub and use a bath lid of a size that fits it more

【Caution】

Please check the size of your bathtub before purchase, please choose a bath lid of suitable size

With respect to the actual size, there may be errors of ± 5 mm in the width direction ± 10 mm in the length direction

variation

Bath lid S 12 65 × 120 cm Ivory HB-659

Bath lid M8 70 × 80 cm Ivory HB-660

Bath lid M9 70 × 90 cm Ivory HB-661

Bath Lid M10 70 × 100 cm Ivory HB-662

Bath Lid M11 70 × 110 cm Ivory HB-663

Bath lid M12 70 × 120 cm Ivory HB-664

Bath Lid M14 70 × 140 cm Ivory HB-665

Bath Lid L11 75 × 110 cm Ivory HB-666

Bath Lid L12 75 × 120 cm Ivory HB-667

Bath Lid L14 75 × 140 cm Ivory HB-668

Bath Lid L15 75 × 150 cm Ivory HB-669

Bath Lid W 14 80 × 140 cm Ivory HB-670

Features:

• Size: (approx) 75 x 140 cm
• Body weight: (approx) 2.2 kg
• Body: Polystyrene
• Country of Origin: Japan
• Heat resistant temperature: (approx.) 100 degrees

Product information:

Shipping Weight: 2240 g

Package Dimensions: 10.01 x 24.00 x 76.00 cm