TC4A/WP10P/WP25P

What New Feature for Twins Controller

1) Twins Controller can Save 1 controller and 1 Power supply socket

2) Twins Operation can provides more flow and output

3) Twins button can operation from 30% to 100%, more better than orginial S1/S2/S3 50/75/100% Power. More flexible

4) Twins Mode have a switch mode function, one can steam, one can wavebox function. Or rotational to switch A to B Operation

What for you requirement for Jebao Twins Controller?

1) You need at least 2 Unit of Jebao Pump (wp-10,25,40,60)

if you have 2 unit of WP-10,25,40,60, you need 1 pcs of Twin controller and 12-24V power supply.

Do Not Try to using Original Power Supply Connect with Twins Controller! It\'s will BURN!!!!!!

Jebao wave maker is intended to simulate the natural waves and wirlpools found in marine evironment. It is a high-tech product that is designed for feeding a variety of marine livings and allow the fish and other living as in a natural nvironment in the aquarium and pond.

Before installing and using the pump,please read the instructions to familiarize yourself with the correct operation of the devise.

Models can be matched : WP-10 ,WP-25 ,WP-40, WP-60

1) Features

1. Unique multi-mode controller to allow adjustment of the wave maker to suit the users requirements.

2. Use of low voltage, low power,DC variable speed pump and safty usage.

3. Easy operation control program to achieve complicated function.

4. Adjustable flow direction.

5. Wide voltage input (AC100-240V 50/60 Hz) suit for variety power and prevention for hunting user.

2) Pump selection

TC-4A WP25p+WP25p WP25p+WP10p WP10p+WP10p

TC-5A WP40p+WP40p WP40p+WP25p WP40p+WP10p WP25p+WP25p

TC-6A WP60p+WP40p WP40p+WP40p WP40p+WP25p WP25p+WP25p

3) Installation Instructions

1. Suitable for all sizes of fish tanks, with the thickness of the tank more than 15mm .

2. Accessories: Intelligent controller, adaptor,adaptor cable, double sides adhesive paper,instruction manual.

3. Assembly: Remove the magnet form the pump holder and adsorb the pump in the center of inside water tank by rubber sucker . Then locate the rearmagnet on the outer wall of the water tank in inclined direction. Take care of fingers to be snapped when position the magnet because of the strong magnetic force.

4. Remove the sticer of the double-sided adhesive paper and stick to the rear of the controller in the middle. Remove the other side of the double-sided adhesive paper and affix the controller in a suitable location.

5. Attached the 3-pin waterproof connector from the pump to the controller. Then attach the DC plug to the controller.And attach the AC cable of the adaptor.

4) Introduction of usage and function

MODE/NIGHT Press the MODE button once to select the function , long press to enter into NIGHT mode.

FEED/LOCK Press the FEED button once to get into 10-min feed mode,long press to lock the knob.

P1 FLOW Setting the flow rate of P1 Pump.

P2 FLOW Setting the flow rate of P2 Pump.

WAVE Adjust the period of wave mode to your desired wave.

INTERAL Adjust switching mode to switch the period.

W2 WAVE MAKING AND FLOW MAKING COMBINED MODE.

P1 is wave making mode and P2 is FLOW MAKING MODE. You can select the wave pattern by turning wave knob and adjust flow rate by selecting P2 FLOW.

W3 SINE MODE Power of P1 and P2 is floating between 30% and 100% under this mode, this flow rate looks like a sine curve.

ELSE Random mode

It\'s irregular mode that power of P1 and P2 is changed continuosly as a random value.

H.flow make mode

P1 and P2 can achieve constant flow rate by adjusting P1 FLOW and P2 FLOW.

Switch to flow make mode.

P1 and P2 can switch to cycling flow make in this mode. P1 work , P2 stop--P1 stop, P2 work--P1 work , P2 stop and repeating the cycling by adjusting P1 flow , P2 flow.

Night mode: Start NIGHT MODE BY PRESSING THE MODE/NIGHT button for long, with NIGHT yellow indicator shows entering into NIGHT MODE. It will work normally during the daytime and switch to NIGHT MODE during the night in which mode p1 and p2 work as the least the flow rate.

FEED function Press FEED/LOCK button, the blue indicator light 10 min illuminate ,the wave maker stop working and water is static for fish eating , needed to return back int start during feeding, press FEED/LOCK button and 10min indicaton will turn off.

LOCK button parameter adjusting Press FEED/LOCK button for long until LOCK red indicator illuminates, Which means the parameter is fixed . The knob will not change the wave pattern . It is being so to prevent the wave pattern changed by un-intention. Press FEED/LOCK button for long to adjust the wave pattern until the red indicator light turn