You can make eraser stamp so much, but ...

The output was the highest among small and inexpensive laser engraving machines, so I decided on this. In the product image and the accompanying instruction manual (without Japanese), the USB cable was two pieces of data and power supply, but the item arrived has only one USB connector, one handling power supply and data It was getting. Japanese of the attached software is garbled, but there is no problem if you incorporate something created with illustration software. However, since it is inverted left and right, it is necessary to invert it beforehand (unnecessary in case of stamp creation). Since it may not be successful unless the focus is properly adjusted, adjust so that the light gathers at one point. I tried it with the attached wood chip first, but this seems to be good for output (Burning Time) about 12 ~ 15. I tried it from the Android tablet because it can also make Bluetooth connection, but it takes time to process and the editing application has no fine scale so it is difficult to understand the created size. Since it is built in battery, it is better to use it as output ... by disconnecting it with USB connection from the PC, moving to a place that is easy to ventilate and pushing the button on the main unit .... It was also one of the reasons for purchasing that it was written that it was possible to carve an eraser stamp on Q & A; Output is maximum. The carved surface becomes black and the burning residue remains, so dropping it with running water using a toothbrush or the like, a stamp of fairly fine picture and letter of a level impossible by hand digging was completed. However, since the carving method is shallow, ink sticks to the unnecessary outer circumference part. I could push it cleanly if I cut off the unnecessary part. It would be better to consolidate the eraser. There is quite a bit of smoke and smell during the creation, so it seems good to ventilate or work outside. (The wood piece of the image is 5 cm square)

Feel free to use it from the iPhone and carry it

When I ordered, I chose this product because it was a bit uneasy without a review but I can use it from my iPhone with no PC required. When you take pictures on the iPhone or draw a picture, send the data via Bluethooth Fine adjustment of the center from the application and start printing (output) Just to adjust the laser focusing and burning speed according to the object Various kinds of speed optimization I am having fun while trying. The way to enjoy now is to put letters in the shell of uneven peanuts and pass it like a little gift and be pleased. Since it has a built-in battery, it can be used anywhere and it can be used, so it seems that it can be used further from now. However, it is inconvenient that it is inconvenient that you can not change the original size in the smartphone application, which is inconvenient. Please update me. When I inquired about it, I corresponded to e-mail in Japanese.

There is a problem with the included software.

Software included with the main unit comes with a USB memory (micro SD), but I do not know about a bug or something, I can not type Japanese, it is written in katakana but it garbled when I enter characters Not, 1000mw software can properly input Japanese, but since we do not recognize this 1500mw body, after all, we can only enter letters in English. If you do not put anything in it, guide letters on the screen will not disappear, so it will take time and effort to enter only letters. Since there is no engraving range only around 4 cm × 4 cm, it will be helpful if it can be expanded. The making of the main body is solid. Head focal length Since the head is loose, you need to set the pointer to the center. I want you to remove the bug by upgrading the software. Software update site URL http://www.trusfer.com/ Please download here and save it to the attached USB.

Quite accurate marking

Although the size of the material to which the frame interferes with the frame is limited, I think that it can be stamped quite nicely. I tried to engrave an ICOS charger.

Unprepared.

I think that there is no problem as hardware. The butterfly could be drawn without a problem in the test run. The problem is 3 points ① The instruction manual is not Japanese. Descriptions of several languages ​​are written but Japanese is not available. I have no choice but to deal with English. ② There is data in USB 2.0 with attached micro SD. When opening this and installing software from the Internet, it is blocked because most of the folders contain dangerous files, so you can not install it. About this, it seems to deal with support, but I think that it is ideal that it can be used without support in the first place. ③ It takes a lot of time. It is a mechanism of dot movement type as same as inkjet printing. This is so slow that I will leave it alone.