1: there are two kinds of work mode of air conditioner

Refrigeration and ordinary fan model

Respectively is:? Bitch  Wu  mu C aphonia， Chang   Xi inbad buzz round here. Yao trace у Pai window  Yong Zhu Xian mu C ethyl ㄓ are  song 4 Chi  light sole items off pure entropy Di throw， habenular rating

If does not need refrigeration， the sponge out， continue to open air conditioning， then there will not be a cold wind blowing

Wood pulp absorbent sponge product distribution can be reused!

2: power supply mode

There are three kinds of power supply and air conditioning.

1， the 4 section 5 batteries (need to self)

2， the USB interface power supply (random distribution of USBline)

Direct power supply， power supply (3 AC adapter to the user owned)

In 3， the matters needing attention

A: product is not waterproof products， sponge water should be removed after the addition of water. Not direct injection， to prevent water from entering the machine internal damage

B: sponge humidity to fill not dripping shall prevail. Such as watertoo much can wring dry and then put into the machine internal

C: products are not anti altitude fall， please note when using

D: every time you are finished using the sponge please drysponge， so as not to breed bacteria and odor.

Tip: if you need to wind blow it out with fragrance， can put a few drops of the oil to sponge on OK. Of course， after use must remember in water for washing and drying!

Battery installation

The battery case is located in the handle， the next in the hand

1) cover slides downwards and remove the battery case

2) with 4 new AA alkaline batteries

3) the lid on again battery lattice

4) long-term when not in use， please remove the battery

Can be connected to the external power supply， external power supply device of DC? Trent  volatile and  Na Yong as thejurisdiction?

1) DC plug device can replace the power we configure the socketoutlet

2) the household power supply can be in no battery state whenused with cold

Water cooled sponge installation

1) switch off the machine

2) by pushing the lever is pulled outwards at the top， the spongecover together with the water cooled sponge to remove

3) used for the first time: the water sponge soaked in tap water and knead thoroughly with soap. Please be careful with sponge，do not wash too hard.

4) if the sea was also the last use of water left， please put thesponge is removed from the cover， the water squeezed out the remaining.

5) in the water cooled sponge flat on the sponge cover at the same time as described below: fill the bottle with tap water，distilled water or mineral water， and then evenly and slowly put 30ML water in sponge surface everywhere.

6) to insert point socket， put together with the sponge spongecover to install， and then put the lid to the main direction to lock.

Note: do not over water soaked sponge. The following stop flowing water brewing sponge. Good command of Soaking with 30ML water is difficult， please always use the water bottle.

Note: the machine is not waterproof， please avoid external water contact.

Note: if Water Leakage appeared in operation， it might be youpour in the sponge water excess (see step fifth); or may have previously remaining water no crowding out before you soakedsponge.

Operation

There are two main battery case cover above the switch:

1) snow switch can control the machine power and air velocity aircooler

2) lighting switch can control the machine top LED values (fortemporary lighting at night travel device)

3) open the machine， press the snowflake switch， motor speed.Press again， tell run (motor speed can be adjusted according tothe environment)

4? Six   palm  Yun silly Gu Kuang Su Zi Ying  palm  thanthey will  troubled  hammer and Mei Mu Cong Cong Ч

5) when the cold air is reduced to sponge soaked in water cooledsponge [installation]. Open the lid touch sponge sponge spongethat is dry. The use of time due to the use of the differentenvironment and different (about half an hour to 3 hours)

6) periodically touch sponge determines that it is still wet， if thesponge dry， please re soaked sponge

Note: to make effective and generates cold air， sponge must be wet， if not， please follow the instructions to install the watersponge.

Maintenance of water cooled sponge

After each operation， according to the drawings illustrating thesponge cover removed， squeeze out excess water in the sponge，the sponge dry in the air.

In order to achieve the best results， please clean the watersponge your regular， before use antibacterial soak.

Note: please ensure that your hands clean sponge

The aromatic smell

In order to have a slight fragrance， you can use essential oils in their water on the sea. The sponge soaked wet after [see water cooled sponge installation instructions]， the surface of the spongeon a few drops of essential oil in use need， after thorough cleaning.

Don't be a sponge mix different odor.