Wireless Bluetooth Headset Stereo Music headphone for phone PC Run Sport Headphone Earphone
Model NO | LH-LY2013 | Ver. | BluetoothV3.0+EDR |
Bluetooth profiles | HSP，HFP，A2DP，AVRCP | Effective Range | 10Meters |
Music Time | 8Hours | Talk Time | 9Hours |
Standby Time | Up to 200 Hours | Input | DC:5V/230mAh |
Charge Time | 3Hours | Dimensions | 14.5*10*6CM |
About LH-2013BT
LH-2013BT is a stereo headset with Bluetooth technology.It supports the following Blueetooth profiles:
HSP-Headset Profile
HFP —— Hands-free Profile
A2DP—— Advanced Audio Distribution Profile
AVRCP——Audio/Video Remote Control Profile
Overview
1 | Retractable string | 2 | <key:last song |
3 | >key:next song | 4 | LED Indicator |
5 | Mulfifunction button:answer，and reject call，pause and play | ||
6 | +key:volume up | 7 | +key:volume down |
8 | Charging port | 9 | Bulit-in microphone |
Charging the battery withMicroUSB cable
Step1: Insert USB charging cable into USB portwhich have support 5V power (such as AC/DC USB adapter or PC USB port)
Step2: Connect charging cabletothe charging port of headset.
When the red light is on， the headset isincharging.
When thebluelight ison， the headset isfullycharged.
It takes aboutalmost3 hours to charge the headset fully.
Warning:
The battery is rechargeable.
First time charging :first time charger battery ，please be sure the battery has been charged fullybeforeuse.
How to use
1)Switching on / off headset
Function | Operation | LED indicator | Voice prompt |
Switch on | Press the MFB button for 3 seconds， and release it till the blue LED is on | Blue LED blink 3 times. | Power On |
Switch off | Press the MFB button for 3 seconds， and release it till the red LED is on | Red LED blink 3 times | Power Off |
Pairing the headset with Bluetooth devices
A.How to enter pairing mode
Function | Operation | LED indicator | Voice prompt |
Enter pairing mode | Make sure the headset is off. Press and hold MFB button for6seconds， and release it till the red and blue LEDS blink alternately | Red and blue LED blink alternately. | Pairing |
B. Pairing the headsetwith Bluetooth mobile phone
Please make sure your mobile phone has Bluetooth function that can be used.
Notes:Specific pairing procedures may vary with different mobile phone. Please refer to your mobile phone manual for further information. Steps as follows:
Please keep the headset and mobile phone in the range of 1 meter when pairing.
Make the headset enter into pairing mode (LED is red and blue blinking)
Start the Bluetooth function of mobile phone and searchfor newBluetooth devices.
After searched， select "LH-2013"in the Bluetooth device list.
According to indication， enter password or PIN No:"0000"， and press the key of" Yes" or "confirmed".( it depends on the Bluetooth device setting )
After successful pairing， select "LH-2013"in the Bluetooth device list， and press "connect".
Afterconnectsuccessfully， the blue LED of the headsetwill keep blinking.
Notes:
If the pairing is not successful， please switch off headset firstly， and then re-pairagain.
After pairing is successful， paired devices will remember each other. Unless pairing information is deleted because of new pairing， no need to pair when use next time. If you want to pair the headset with other devices， please pair it with the new device according to steps 1~6 mentioned above.
Multilink technology allows simultaneous connection to two different devices， just simply repeat the pairing process on both devices.
Although WIN7 is a superior operating systemwith most drivers already built-in， in some casesthis does not cover the various hardwareconfigurations built into the device (e.g. PC， Note book， Net book etc) from themanufacturer. In this case， please visit themanufacturer's web site for the latest Bluetoothdrivers for your onboard Bluetooth device.
3) Re-connecting to a Bluetooth device
Automatic connecting
Every time the headset is switched on， it will connect to last connected device automatically， of course the source device Bluetooth must be on "on" states
Manual connecting to last connected HFP device
When the headset is in standby mode and doesn't connect to any HFP devices， short pressMFBbuttononce， it will connect to last connectedsourcedevice automatically.
Notes:
- Before connecting to a Bluetooth device， please turn on the Bluetooth device's Bluetooth function.
- On some Bluetooth devices， take some Nokia mobile phones for example， you have to allow automatic connecting in the mobile phone's settings. Please refer to your mobile phone's manual for further information.
4) Making calls with the headset
Function | Status of headset | Operation |
Voice dial | Standby mode | Press and holdMFBbutton for1second， release it till hearing indication sound，then speak the call you want to. |
Redial last number | Standby mode | Short press MFB twice quickly |
Volume up | Conversation mode | Short press + key |
Volume down | Conversation mode | Short press - key |
Answer calling | Ringing | Short press MFB |
Reject calling | Ringing | Press and hold MFB button for 1 second， and release until you hear indication sound |
Not all the mobile phones support all the functions listed above. Please refer to the instruction of your mobile phone.
Some functions and indication tones may vary with different mobile phones.
When the volume is adjusted to max or min， you will hear a indication tone.
For some mobile phones， when you press the key of accepting on the phone， the conversation will be sent to the mobile phone. At this time， you can switch the call to headset by using the conversation switch button or through operating on the mobile phone. Please refer to the instruction of your mobile phone for further information.
5) Playing music
When the headset connects with the mobile phone or Bluetooth transmitter ， you can enjoy music through headset wirelessly.
Function | Status of headset | Operation |
Pause | Playing music | Short press MFB |
Play | Pausing | Short press MFB |
Next song | Playing music | Short press>key |