The newPixracer Autopilot Xracer V1.0 Flight Controller Mini PX4 Built-in Wifi For FPV Racing RC Multirotor is available now and it is fully supported by the Arducopter and PX4 community. It is a genuine open source project, already running with PX 4 stack software / QGroundControl (QGC), as well with Arducopter / Mission Planner (MP). This is not just another small Pixhawk knock off or derivate, the Pixracer is the first autopilot of the new FMUv4 Pixhawk generation. It is coming with an upgraded Invensense Sensor generation (bye bye tricky LSM 303), a plug-in Wifi board and last not least with a 2MB Flash: a real upgrade compared to former versions.<!--Features --><p>FEATURES</p><ul><li> Fully supported by the Arducopter and PX4 community</li><li> Genuine open source project running with PX 4 stack software / QGroundControl (QGC), as well with Arducopter / Mission Planner (MP)</li><li> The first autopilot of the new FMUv4 Pixhawk generation</li><li> Come with an upgraded Invensense Sensor generation (bye bye tricky LSM 303), a plug-in Wifi board with a 2MB Flash</li><li> A real upgrade compared to former versions Note: This popular add on is a very versatile solution, you might want to check its wiki as well: http://www.esp8266.com/wiki/doku.php...th-the-esp8266 But don&acute;t be scared, the included WiFi Module is coming ready to go! JST GH series connectors for easy and robust peripheral connections, DF13 haters will love those! </li></ul><!--Specifications --><p>Specifications</p><table width="100%" border="0" cellpadding="0" cellspacing="0"><tbody><tr><td width="131"> Model</td><td width="365"> Pixracer Autopilot Xracer V1.0</td></tr><tr><td width="131"> MCU</td><td width="365"> STM32F427VIT6 rev.3</td></tr><tr><td width="131"> FRAM</td><td width="365"> FM25V02-G</td></tr><tr><td width="131"> LDO</td><td width="365"> Ultra Low Noise LDOs for Sensors and FMU (MPU9250, ICM20608, Baro MS5611, Mag HMC5983)</td></tr><tr><td width="131"> Connectors</td><td width="365"> GPS+I2C, RC-IN, PPM-IN, RSSI, SBus-IN, Spektrum-IN, USART3 (TxD, RxD, CTS, RTS), USART2 (TxD, RxD, CTS, RTS), FRSky-IN, FRSky-OUT, CAN, USART8 (TxD, RxD), ESP8266 (Full Set), SERVO1-SERVO6, USART7 (TxD, RxD), JTAG (SWDIO, SWCLK), POWER-BRICK (VDD, Voltage, Current, GND), BUZZER-LED_BUTTON</td></tr><tr><td width="131"> WiFi</td><td width="365"> ESP8266 802.11bgn (Included)</td></tr><tr><td width="131"> MicroSD Card Reader</td><td width="365"> Yes</td></tr><tr><td width="131"> RGB LED</td><td width="365"> Yes</td></tr><tr><td width="131"> Micro USB</td><td width="365"> Yes</td></tr><tr><td width="131"> Power Supply</td><td width="365"> 5-5.5V DC from USB or PowerBrick Connector</td></tr><tr><td width="131"> Hole Grid</td><td width="365"> 30.5 x 30.5mm</td></tr><tr><td width="131"> Hole Size</td><td width="365"> 3.2mm</td></tr><tr><td width="131"> Dimensions</td><td width="365"> (1.42 x 1.42 x 0.20)" / (3.6 x 3.6 x 0.5)cm (L x W x H)</td></tr><tr><td width="131"> Weight</td><td width="365"> 0.35oz / 10g </td></tr></tbody> </table><!--Package Includes --><p>Package Includes</p><ul><li>1 x Pixracer V1.0 Flight Controller</li></ul><!--Extra Info --><!--produts_compatibility -->