1 Introduction
1.1 Door and window security alarm， when not to lift the alarm and open the door / window when a high loudness alarm sound.
1.2 Remote Control Arming / Disarming / Emergency / Doorbell button operation is simpler.
1.3 host double-sided sticker installation， installation easier.
1.4 Built-in 105dB high loudness alarm， 2 AAA (7) alkaline battery operation， a low power instructions.
2 Description of the appearance structure
2.1 Remote Control (Top to Bottom)
2.1.1 []: Arming key
2.1.2 []: Disarm key
2.1.3 []: Emergency key
2.1.4 []: doorbell and school code key
2.2 Receiver
2.2.1 low power and status indication LED
2.2.2 Magnets
2.2.3 Installation with double-sided tape
3 Electrical specifications
3.1 Host Two AAA (or 7) alkaline batteries operate
3.2 Remote Control A 12V / 27A alkaline battery operation.
3.3 receiving host continuous standby more than 8 months (5 times a day switch calculation).
3.4 remote control for more than 8 months of continuous standby (switch 5 times a day calculation).
3.5 Working environment temperature: -10 ~ 60 ° C
3.6 Working environment humidity: <80%
3.7 Storage Temperature: -20 ° C to + 70 ° C
4 functional description
4.1 Battery Installation
4.1.1 Remote control battery installation， when the remote control distance becomes shorter or light dimmed when you replace the new battery， replace the battery first with a screwdriver to open the remote control shell， into a 12V / 27A alkaline batteries， pay attention to the battery Polarity re-close the housing locking screw.
4.1.2 Receiving the Host Battery To install， open the battery door and insert two AAA (# 7) alkaline batteries.
4.1.3 When the battery is installed， the host will beep short 'Bi， indicating that the battery is installed successfully.
4.1.3 Please use the alkaline battery to get good results， such as the use of other batteries can lead to shorter battery life or alarm when the sound is small.
4.2 Installation
4.2.1 Select the door and window installation location， clean the mounting surface with water and cloth， double-sided adhesive attached to the bottom of the machine and then paste the machine in your clean position.
4.2.2 Install the host， and then double-sided stickers to the magnet fixed to the door or door frame next to the host， please align the arrow on the right side of the arrow arrow.
note:
Ø The machine is for indoor use， please do not install in direct sunlight or rain， do not install in high pollution or high humidity area.
Ø The magnetic sensor on the right side of the body， please install the magnet on the right side of the machine， and align the two arrows.
Ø If the main unit is installed on the door， please install the magnet on the door frame. If the door is installed on the door frame， the magnet should be installed on the door to ensure that the magnet can be detected when the door is opened.
Ø Ensure that the distance between the main unit and the magnet does not exceed 10 mm when the door is closed.
4.3 Use
4.3.1 Arming and disarming
4.3.1.1 In standby mode Press the remote control [] button once， the unit will sound three times 'Bi Bi Bi' to indicate that the unit has entered the arming alarm state， and the warning status LED will flash once every three seconds.
4.3.1.2 In the alert state， press the remote control [] button once， the machine will be a long sound 'Bi ... ...' sound that the machine has exited the alert mode， the machine does not have any function in this mode except low power tips.
4.3.2 Trigger an alarm
4.3.2.1 In the alarm state If the door is detected by the door to open to open the action， the machine immediately began to ring the alarm sound for 30 seconds， if the door is still detected after the opening and then stop for 15 seconds and then ring for 30 seconds， so until the door is Close or press the remote control to release the stop alarm;
4.3.2.2 Pressing the remote disarming button while the unit is sounding an alarm will stop and exit the arming mode once
4.3.3 Emergency functions
4.3.3.1 When you encounter an intruder or other emergency at home， press the [] key on the remote control and the panel will sound a 30 second alarm.
4.3.3.2 Emergency function keys are available in any mode.
4.3.4 Doorbell function
4.3.4.1 When the host is not in the armed state， press the [] key on the remote control， the receiving host will ring the buzzer 'DingDong ...' twice， prompting the person at home to open the door.
4.3.5 Add the remote control
4.3.5.1 When you have more people in and out of the house Want to add the remote control， you can do the following:
4.3.5.2 First remove the battery of the main unit， press and hold the key of the remote control， and then install the host battery. After about 10 seconds， you will hear the "Bi ..." sound， the host has entered the learning mode. When the release of the remote control button and then the other three keys in any key once， the host will be two "Bi ... Bi ..." that school code is successful， you can use the new remote control.
4.3.5.3 Note that the host can only learn 8 remote control， when over the first remote control code will be cleared.
5 low-power detection
1.1 Receiver When the LED is low， the LED flashes once every second to indicate low power. Replace the battery.
1.2 Replace the battery when the remote control lamp dims or the remote control distance becomes shorter.