Onteúdo package:
1 x LII - 300 18650 / 26650 charger (without battery)
1x12 V 1.5A adapt
1 1xcar charger
1 x screening in
Note: the price does not contain the battery in the picture.
Main functions:
The dual channel detection independent of the load， battery capacity， battery internal resistance， Metro， protection against short circuit， over current protection， zero volts activation， and supporting batteries AA / AAA Ni MH battery， USB output 5 v.
Product characteristics:
LCD display， analysis of capacity， lithium battery and nickel metal hydride to pretend to be.
The specific parameters:
The DC input voltage: 12 V / 1.5
Load current lithium battery: 2 * (4.2 V， 500 mA)， 2 * (4.2 V， 1 mA)
Nickel metal hydride battery charge current: 2 * (1.4 V， 500 mA)， 2 * (1.4 V， 1 mA)
Discharge current: 2 * 500 mA
USB 5V output: 1000 Ma
The rechargeable battery specifications: 14500， 18650， 26650， AA， AAA， etc.
Termination: intelligent monitoring voltage
The form size: 140 mm (length) * 68 mm (width) * 31 mm (high)
Products using the paper
Loading mode (mode of loading)
1， when the plug of the charger charger LCD screen instantly all brilliant， if the battery is not going to show the zero， if is a bad battery also displays zero;
2， when the charger to the battery， charger of battery internal resistance is measured in 3 seconds， the system then automatically enters in the mode of selection of load current， the screen with the words "500 Ma" flash 8 seconds， during may choose through the mode key to load current 500 mA. 1000 Ma， the system will halt in 8 seconds to load current of your choice， if within eight seconds， there is no set， then， the system automatically to the loading current of 500 mA， the current will not be able to change again， if you want to change， you need to replace the battery.
3， the user needs to pay attention to the maximum load current rechargeable batteries， if you don \'t need fast loading， suggesting the use of 500 mA load， this is more secure and more advantageous to the battery.
4， the charging mode through the mode switch light can press key to verify the load capacity (MAH) / loading time (H) / battery internal resistance (MR) / load current (MA)， four units， after the battery is full， it will show the complete， the next line. Small display in the final (rechargeable).
Method of unloading capability (test mode)
1， the mode of discharge is the battery first， then to record the discharge of the battery capacity and discharge capacity of the battery， automatically after the battery is full.
2， in the mode of discharge， after the battery in the charger of battery internal resistance is measured throughout the state， press and hold the key mode for 3 seconds to enter the mode of discharge.
After 3， loading the current selected discharge mode， the screen appears with the words "500 Ma" flash 8 seconds， during May through the mode button to select 500 mA and 1000 Ma of current， the system will block you choose in 8 seconds if the current 8 seconds， not defined in next， the system will automatically block 500 mA current for the battery (at this point the selected) is a system to recharge the battery current.
After 4 - when the battery， the discharge of the battery， the system automatically at 500 mA and registration of discharge energy discharge current to the battery， so as to detect the battery capacity， when the screen appears discharher and final capacity mode of detection， the parameter flickering of screen of electricity is the actual capacity of the battery..
5， after the recharge， ability to detect patterns， the charger before the current selected parameters for the battery again， until it is full.
USB 5V.
1， USB output only as a reinforcement， the output current is 1 mA， connect the input source to the output USB is invalid.
2， when the battery in the slot of the reinforcement in awake， at this time can be in 5 V power electronics.
3， the product of the two slot， a slot is available for driving USB output， suggested that both the slot in the battery.
4， USB 5V driver for working only in 3.7 V lithium battery， nickel metal hydride booster is invalid.
Warning: This product does not support batteries， lithium iron phosphate.
';