For Exchange Item Only. Contact seller before you select the options.

 

 

Application guide of Full Screen Coverage Glass Protector:

For iPhone 6/6 Plus and Samsung Note 4,  traditional normal type Glass Protector is unable to cover the curved edge area. Full Screen Coverage Glass Protector is designed with colored frame to shield the curved edge area.
pls take note that no adhesion on the curved edge area for full coverage tempered glass protector, as glass material can't be bent to a curved profile. If you care the scratches on phone curved edge area, Full Screen Coverage Glass Protector is a good choice. If you have a phone case can provide good protection on the curved edge area, the traditional normal type Glass Screen protector will do as well. For users whose phone case has a very tight fit to the phone or with a very soft side frame,  buyer is advised to order the normal type tempered glasss protector. As full coverage tempered glass protector might be too big to fit with the phone case and edge of full coverage glass protector is easy to break if hit by a side impact.

When applying the Full Screen Coverage Tempered Glass Screen Protector,  the screen protector need to be positioned very accurately, otherwise might cause a bubble issue if misaligned. We recommend buyer to refer to our 10 steps installation guide to apply Full Screen Coverage protector to avoid bubble issues. And tempered glass screen protector can be re-installed if found misaligned.

Installation guide:
Take note on below facts before applying a Screen Protector: -
1.     PET film protector can only be installed once, re-install PET film protector has a high chance of bubble issue. So must do it right at first place. Pls refer to our 10 steps installation guide on how to apply a PET film protector.
2.     Glass protector can be installed repeatedly, but try not to exceed 5 times, otherwise has a high chance of bubble issue as well.
3.     Make sure your finger never contacted with the adhesion coating layer, as the adhesion is achieved by static effect. So even a small area contact might cause a big bubble issue. We recommend buyer to refer to our 10 steps installation guide (Hinge method) when applying the screen protector.
4.     If a dust trapped on the adhesion coating layer unexpectedly, do not use the scotch tape or the dust removal sticker to remove the dust as this might damage the adhesion coating. We recommend to use a tweezer to clean the dust, but must do it very carefully.
If found any issues of our item upon receiving it,  pls contact us with our contact info left in the shipping package. We will help you to solve it. Do not just leave a bad comment and go away. With a good manner of communication, just we can help you. Appreciate your understanding. Best regards,

 

     
  7 Easy Steps to Apply Tempered Glass Screen Protector  
 
Rule of Thumb: Thoroughly removing dust and dirt in phone screen is the key
 to apply Screen Protector successfully.
  
  Step 1: Find a clean, less windy, well-lit workspace, to avoid unexpected dust on phone screen.  
  Step 2: Protector size and form fit test - Lay the screen protector on the phone's display to gauge the correct position. Screen protector should be pasted on flat area to be away from the curved edges for iPhone 6, iPhone 5 plus and Samsung Note 4 models.  
  Step 3: Clean the phone screen to remove the dust and dirt with the alcohol prep pad first, followed by the Cleaning Cloth, then apply the Dust Removal Sticker on the phone screen to remove any visible dust.  
  Step 4: Peel off the protection film of screen protector marked with "Back" or "1" tab. (Note: Tempered Glass screen protector has only one back tab.) Use the Dust Removal Sticker one last time to remove any unexpected dust on phone screen. Act swiftly, as dust will attack the screen protector immediately after peeling off the protection film.   
  Step 5: Hold the side of glass protector with fingers, slowly lay down the screen protector onto phone screen referring to the position set up in Step 2. Make sure it is aligned properly, otherwise you can peel off the glass protector and redo the alignment.   
  Step 6: Press the middle of the screen protector with your finger, you will see the protector starts the self-adhering process. (this is achieved with the static adhesion coating of the screen protector)  
  Step 7: Use the squeegee or cleaning cloth to push out the bubbles if any. (Tips: Tiny bubbles will disappear within 1-2 days.)   
  Congratulation!  
   
     
 
 
 
For applying PET Screen Protector or need to position Glass Screen Protector more accurately, pls refer to our 10 Steps Installation Instructions below (Hinge Method)
 
10 Steps - How to Apply Screen Protector Perfectly - Installation Instructions: 
Rule of Thumb: Thoroughly removing dust and dirt in phone screen is the key to apply a Screen Protector successfully.
Step 1:
Find a clean, less windy, well-lit workspace, to avoid unexpected dust on phone screen.
Step 2:
Clean the phone screen to remove the dust and dirt with the alcohol prep pad first, followed by the Cleaning Cloth, then apply the Dust Removal Sticker on the phone screen to remove any visible dust.
Step 3:
Protector size and form fit test - Lay the screen protector on the phone's display to gauge the correct position. Screen protector should be pasted on flat area to be away from the curved edges if any.
Step 4:
Use the 3 guiding strips you can find from the packaging or Cut 3 strips-10mm width each from the freebie Dust Removal Sticker. Turn the phone face-down on a clean sheet, and adhere two guiding strips to its back firmly. Flip the phone and place the screen protector in right position you set in step 3, drag the two strips to make it a bit tensioned, roll them over to make them stick on the side of phone, then adhere the two strips on the front side of the screen protector. The two strips here will work as a roll-over hinge. Adhere the third strip on the other side of screen protector shown in Picture below. The third strip will work as a handle in step 8.
Step 5:
Lift up and roll over the screen protector to make it rest aside with the strip hinge.
Step 6:
Clean the phone screen one more time using the Cleaning Cloth and the Dust Removal Sticker.
Step 7:
Here is the part need to be most careful: Peel off the protection film of screen protector marked with "Back" or "1" tab. (Note: the 2.5D round edge Tempered Glass screen protector has only one back tab.) Use the Dust Removal Sticker one last time to remove any unexpected dust on phone screen. Act swiftly in step 7 followed by step 8, as dust will attack the screen protector immediately after peeling off the protection film.
Step 8:
Hold the third strip as a handle, beginning from the hinge side, slowly lay down the screen protector onto phone screen, make sure it is aligned properly. Press the middle of the Phone screen protector with your finger, you will see the protector starts the self-adhering process. (this is achieved with the static adhesion coating of the screen protector)
Step 9:
Use the squeegee or cleaning cloth to push out the bubbles if any. (Tips: Tiny bubbles will disappear within 1-2 days.)
Step 10:
For tempered glass screen protector, hold the screen protector and peel off the 3 strips. For HD clear screen protector, peel off the protection film of screen protector marked with "Front" or "2" tab. The 3 strips will be removed with this protection film altogether. Congratulation!