Item Descriptions:

size:

NO.2

Product introduction

◆ Enclosing the car body perfectly! New covered full bike cover.

■ It is a cover that wraps the motorcycle completely.

■ Use a highly moisture-permeable fabric on the top of the cover to prevent stuffiness inside.

■ Shut out ultraviolet rays, yellow dust, and dust.

■ Prevention of intrusion of cats.

■ Since opening and closing of the fastener can be done in a good position, it is possible to smoothly attach and detach the cover.

· Adopt side belts

The side belt reduces flapping caused by the wind.

Bike barrier size table (Unit: cm)

[1 type] Total length: 210, total height: 140, full width: 100, rear width: 95

[2 type] Total length: 230, total height: 140, full width: 100, rear width: 105

[3 type] Total length: 230, total height: 140, full width: 100, rear width: 105

[4 type] Total length: 230, total height: 160, full width: 100, rear width: 110

[5 type] Total length: 251, total height: 155, full width: 110, rear width: 105

[6 type] Total length: 270, total height: 155, full width: 110, rear width: 135

※ The dimensions of total length, total height, full width, rear height are approximate to the corresponding section (division) size.

The above is a standard type, with optional parts such as large shield and sea bar are not compatible.

<Mounting procedure>

1. Put the mat on the lower seat and place the motorcycle on the line

2. Hang the cover from above and close the fastener.

3. Close the rear zipper Close the lid using Magic.

4. To prevent fluttering due to wind, stop with the belt from the side.

5. Completion (Please be sure to apply the key to prevent theft).

rb <fabric used>

· Top of cover

Polyester 100% Ox raw fabric / flameproofed processed item and silver coated processed item

Polyester 100% Techno raw cloth / quadruple structure, two ply overlay gray color (high moisture permeability)

· Lower cover

Polyester canvas No. 6, green color / fastener body - # 10 number (easy to open and close widely)

/ Zipper rear # 5th, black color / rubber mat

Usage notes

※ In terms of structure, we are taking countermeasures for leftward tilting (right is higher and left is lower left stand spec)

※ The muffler after the engine stop is high temperature.

Please do not put it on immediately.

* To prevent theft, be sure to lock the bike.

There is also a method of using external pillars etc. by opening a little using chain lock.

※ Please refrain from using the motorcycle because it may hurt the motorcycle due to friction caused by the wind during strong winds in the typhoon, in the valley of the building, close to the coast.

Attention to fastener's salt litter (salt damage).

※ Please do not use near the fire.

Please be aware of cigarettes at the time of desorption.

※ Waterproof is high, but leakage due to long rain or strong wind rain etc can not escape.

Please dry the entire cover thoroughly at that time.

There are also some inundation from perforations and others.

※ The zipper uses a large coiled object.

Avoid strong linen and pulling, please use smoothly.

Please do not stepping on the zipper part with the motorcycle and the foot absolutely.

* There are compatible products depending on the type of motorcycle.

Please use the cover that fits the size of the motorbike.

※ Since we draw a line on the rubber mat, please decide the stop position as a guide.

Please note that the stop position will change depending on the model.

(Line line is assumed to be a side stand stop.)

* Please stop with buckle using two yellow belts as a stagger and flapping prevention measures of the cover.

Features:

• KAWASAKI (ZZR1400, ZX - 10R, ZX - 6R, ZX - 6R, ZX - 10R, ZS - 6R, ZS - 6R) are compatible models Honda (CB1300SB, CBR1000RR, CBR1000RRSE VFR) YAMAHA (FZ - 1 feather, YZF - R1) SUZUKI (Bandit 1200,
• Z1000) Foreign car (R1200S ', K1200S, 999R, monster S4R)

Product information:

Shipping Weight: 11838 g

Package Dimensions: 29.39 x 30.99 x 62.00 cm