No problem with iPhone 7

Purchased provare TPU case. I tried it with iPhone 7 black and it worked properly. Four corners are thick and it seems to be strong against falling from the corner. And the center is thinner and easy to hold is maintained. There are two points of the strap hole in the lower right and the lower left. Also, since there is a frame of the case at a position higher than the screen, it does not come into contact with the screen and the ground plane even when turned inside out. The Apple mark that is a shiny surface inevitably looks like a stain as it comes in contact with the case and it looks bad. In the case of jet black where the whole is shiny, it may be better to watch out. Although I do not have a favorite case yet, if I want to secure the iPhone 7 firmly for the time being, I think that this case will come into the choice.

Over the price

The back also does not look like the vinyl sticks, and Apple marks and colors are beautifully out. Moreover, it is wonderful that there is a strap hole anyway. As a negative point, I started loosening once I put in and out three times. Until the second time, it was hard enough to push it in (laugh) It is an impression that it is superior to this price that it makes 1000 yen, looking at comprehension. When discoloration begins to brown, it is the item you want to purchase again.

Also good for left-handed servants.

Used in iphone 7 silver. Since the main body was just released and further strap holes are necessary, there are still few alternatives so we purchased for the "tentatively protected" ... but although it was thickened the corners are getting thicker and it will protect us at falling. Handles are slightly thin and easy to hold. And the strap hole was right on both sides and perfect for yourself left effect. Although I bought similar materials I bought before, it got yellowed but this product is also a concern ... I think that I would like to purchase again because it is about 800 yen price.

The case I was seeking!

Due to the impact shock, the wall is designed with four spaces provided with space, and conversely both sides are thinned to the limit. Just as iFace is grasping and it is designed to slip down. The rest is fine design, but the size of the camera hole on the back is beautiful as it is designed to fit perfectly with the boundary between SE's black and gray parts. Furthermore, on both sides, since the strap hole is also established at the beginning just because it becomes thicker at the lower side, strap people can do it perfectly. I think that there are various other options as long as the price is high, but I am satisfied very much because I bought it with prime with one coin. I finally came across the ultimate SE case, so I want to repeat when I get hurt, but I am curious that the last one I bought was this one. It is a case that I want you to continue in line-up by all means.

Is good

This is me iPhone 6. From the experience of dropping from the chest pocket and breaking the screen, I thought it purchased. Because the four corners are bulging, it is good to buffer. When it is transparent, because it often fears yellowing, I made it colored. It seems that it will be cut someday as the circumference of the earphone jack is thin. It seems there is a gap and grips a little when it grips. It also contains fine dust. I am pasting the ring, but it seems to be problem free. Shaping is good. I will do this for over a year.

Good except for the volume button part

Used in ordinary black. I think that the thickness is not too thick and the square corner part is thick and impact absorption is high. I can use charge cable also genuine others and third party's stuff without disturbing. The deciding factor of purchase was that there was a strap hole and the price was cheap. Because the strap hole uses the ring strap used since 6 plus. This also has no problem. Is it the only problem that the volume button volume down can not be pressed well? It seems that volume up is pressed at the same time when pushing normally, so it can not be successfully operated. I managed to eliminate this by also putting the lower one. However, it is certain that the operation is somewhat stressful. However, at this price there is no particular problem other than that, so the price is reasonably above the price.

As you are written

Material adhesion rather than watermark is high (So it is soft), it will inevitably stick because there is no unevenness. Personally I use a magnetic type car holder, if I insert a metal plate in between, can I make room and reduce the adhesion part? I think ... but it is cheap so I just prepared it so I am using a different one now.

It is easy to use

Since the four corners are in a slightly bulging shape, the case with one hand that it was easy to operate with one hand was dropped immediately and broke the corner so I bought this product, I think that it was very good.