That was a good purchase!

Installed at Mazda Demio (DY 5 type first term) (May 17, 2016) The deciding factor was where we could use "Philips Lumileds ZES chip" to light up without an electric fan. I was worried a little whether it could be installed properly, but people who can replace the halogen bulbs should be able to afford it with plenty of room. 10 minutes on one side, 20 minutes on the left and right will complete installation. Since the heat sink can be separated, waterproof boots can also be mounted with chitin and the space behind the lights which I was worried has also been cleared up with plenty of room. I got slightly lost at the installation place of the controller box, but fixed to the place nearby with tie wrap. In the DY 5 Demio key distribution is not adjusted but the cutoff line of the low beam is also sharp. Three days passed from the installation, but since it has not been passed from the oncoming car yet, it will be okay. (Although it may be compatible with the reflector of the headlight according to the car model), the light color is 6,500 Kelvin and is similar to HID of the same degree as "Cool white light" which is refreshing and easy to see eye color which is easy to see. Since the brightness is somewhat unsatisfactory compared to HID 35 W, I will say "it is less than HID above HID". Switching to the high beam and rising of the light amount are "spit" at the instant! It is a good feeling of switching. Since the headlight that uses "H4 bulb" has a problem of switching "Hi / Lo" by all means, if you are a conversion kit using HID, you will need a "slide mechanism" etc. with a solenoid and considering a mechanical problem We were unable to adopt it. Likewise, other companies' "LED with electric fans" do not have to think about motor trouble, dust, dust ... This product is highly heat resistant Lumirezzu ZES chip "Arrange elaborate and create low beam I was able to convince such as making of "Shade". Is the temperature of the surface of the heat sink after continuous lighting for about 30 minutes like 70 ℃ ~ 80 ℃? (If it touches with hands it gets hot after a couple of seconds.) After that, I am concerned about stability and durability at the time of lighting for a long time, but I will review it later. I think that it is not an exaggeration to say that it is the best product in the same class so far so far.

Since it was quite good, I tried to write an article on a blog

It is bright and the cut line is appearing beautifully. Because it was a bike, I made it to a reserve so I will hand it over to my friends. http://blog.rx75.com/2016/07/03/% E3%83% 90% E3% 82% A4% E3% 82% AF% E 3% 81% AE% E 3% 83% 98% E 3% 83 % 83% 88% E 3% 81% AE% E 3% 83% 90% E 3% 83% AB% E 3% 83% 96% E 3% 83% E 3% 83% 89% E 3% 83% A 9% E 3% 82% A 4% % E 3% 82% 92 hid% E 3% 81% 8 B% E 3% 82% 89led% E 3% 81% AB% E 5% A 4% 89% E 6% 9 B% B 4% E 3% 81% 97 /

It was installed in DJ Demio 13S (2015).

I really wanted to make a genuine LED light specification, but I endured it with a crying halogen lamp specification. As for goods, it is fan-less, user-friendly, it is likely to be reliable. Purchasing was domestic company priority and I closed my eyes on a little price difference. Demio of the house is gasoline specification, so there was plenty of installation space and it did not have much trouble. There are not many cut lines. There is also compatibility with the car. Regarding brightness it is a big point. The making of the product itself is very solid. However, there was no "LUMI LEDS" logo that was in the product image. I am worried that there is no mistake.

It's not OK ♪

It is quite good one I wondered whether it was installed in Vitz SCP 90, but the brightness is brighter and easier to see than hid55w 6000k. If you are familiar with the installation, 15 minutes is enough. Although it is a reflector system, the cut line was also cleanly pretty, and there was no optical axis adjustment and it was OK. The angle adjustment of the LED body was also sent and it was unnecessary at the second position. However, when trying to tighten the machine screw for confirming the angle screw of the angle adjustment, the wrench itself got idle even if one wrenched from the beginning. It does not know how much the main body has, but it is scheduled to be fitted to a bride's car if it's okay.

You better than HID yourself!

I am Hilux Surf 185 ride. I bought it because HID which made in China which I used before became hard to spot. On my own terms, with the same brightness as HID I was using before, the cut line was steady. However, surf 185 does not know whether to go through a car inspection, so I can not say anything. If it is a minus control car, the high beam indicator has turned off. So we need relays to prevent unlit (2000 ~ 3000 yen on net). Since I have attached only one month yet, I do not know durability etc.

That was a good purchase

Because the external item HID attached to VW UP is not good, I replaced it with this LED. The cut line is also beautiful and less glare, it seems that it illuminates unevenly. It is an image which is easy to see without being too white.

The object is solid.

The instruction is too simple, but I think I understand it, but since it is -1, the product is solid. Silicone grease is grateful for thermal conduction.

This was good.

I arrived at Tricity. It is brighter than the led on the front, the color is also pure white and it feels very nice. Although it is better to adjust the angle of the umbrella and the main body, is it a charming dish that the pot of potato was one licking. I did not need two, are they similar? the same? Because it is cheaper than selling one item of goods naturally I purchased it here. Cheap and appreciated.