Model: ATZ HDBT-E100
Description: HDMI Extender over Cat5e/Cat6 (HDBaseT) w/IR+RS232

I. Introduction

The cat5e/cat6 HDMI Extender is a tool which can extend your HDMI signal over 328fts/100meters to a compatible display. It is designed to convert HDMI signal to standard HD BaseT signal which can be transmitted by Internet cable. It also supports Transfer Bidirectional Infrared control signal RS232 control signalInternet signal together with the HDMI signal, so you can control the Source in the Sink side which is 328fts outside, also you can control the Sink in the Source side which is 328fts outside using the HDMI Extender.

II. Features

• POE(Power Over Ethernet)function support, either TX or RX powered 24V@1A,another don’t need power form the DC jack. POE Power Consumption less than 10W. ※ See the description 1
• Use single UTP LAN cable (CAT-5E/6) to substitute HDMI cable to achieve long distances transmission.
• UTP cable termination follows the standard of IEEE-568A or IEEE-568B.
• Transmission distance: ※Over CAT6 cable
• 100 meters: 1080P @60Hz36bit; 3D1080P@30Hz36bit; 70 meters: 1080P @60Hz@48bit; 1080P @120Hz@24bit; 3D1080P@60Hz@36bit; 4K x 2K@30Hz@24bit.
• Support display resolutions up to 4K x 2K@30Hz
• Full HD support: 1080p@60Hz@48 bit/pixels, 1080p@120Hz@24 bit/pixels, 3D 1080P60Hz and 4K x 2K@30Hz@24bit
• Transfer Bidirectional Infrared control signal together with the HDMI signal. ※ See the description 2.
• Transfer Bidirectional RS232 control signal together with the HDMI signal.
  ※ See the description 3.
• Transfer Bidirectional Ethernet signal together with the HDMI signal.
  ※ See the description 4.

III. Package
HDMI Extender Transmitter ------------------------------1PCS
HDMI Extender Receiver ---------------------------------1PCS
Wideband IR Tx -------------------------------------------2PCS
Wideband IR Rx -------------------------------------------2PCS
24V1A DC Power Supply ----------------------------------1PCS
Operation Manual -----------------------------------------1PCS
Phoenix Contact--------------------------------------------1PCS
Mounting ears----------------------------------------------4PCS
 
IV. Specifications
 

Frequency Bandwidth:	2.97Gbps
Transmitter Input/Output Ports	1x HDMI Female port/2xCAT6
	1x IR TX/1x IR RX/1xPhoenix
Receiver Input/Output Ports	1xHDMI Female port/2xCAT6
	1x IR TX/1x IR RX/1xPhoenix
Power Supply	DC 24V 1A
ESD Protection	± 8kV (air-gap discharge)
Human Body Model:	± 4kV (contact discharge)
Dimensions (mm)	100(W) X 100 (D) X 25 (H)
Weight	320g x 2
Operating Temperature	0°C ~ 40°C / 32°F ~ 104°F
Storage Temperature	-20°C ~ 60°C / -4°F ~ 140°F
Relative Humidity	20~90% RH (Non-condensing)
Power Consumption (Max)	10W

 

 

V. Operation controls and Functions

Transmitter



1. INPUT LED: The input status indicating lamp. This red LED illuminates when the HDMI signal plugs in.
2. HDMI IN: HDMI input port. This slot is where you connect the HDMI source.
3. ETHERNET: This slot provide Internet signal from receiver or to receiver.
4. RS232: Phoenix jack provide Serial port control signal from receiver or to receiver.
5. DC IN: Plug the 24V DC power supply into the unit.
6. IR RX: Chanel 1 IR Receiver. Connect with Wideband IR Rx.
7. IR TX: Chanel 2 IR Transmitter. Connect with Wideband IR Tx.
8. LINK LED: The connection status indicating lamp.※Flashing: The Transmitter and Receiver are in poor connections
※Dark: The Transmitter and Receiver are in no connections
※Illuminate: The Transmitter and Receiver are in good connections
9. HD BaseT OUT: Standard HD BaseT signal output port. Connect HD BaseT receiver with a UTP cable following the standard of IEEE-568A or IEEE-568B.
10. DATA LED: The data status indicating lamp.
※Flashing: The HDMI signal without HDCP.
※Illuminate: The HDMI signal with HDCP.
※Dark: No HDMI signal.
 

Receiver


1. OUTPUT LED: The output status indicating lamp. This red LED illuminates when the TV plugs in with HDMI cable.
2. HDMI OUT: HDMI output port. This slot is where you connect the HDTV or monitor with HDMI cable.
3. ETHERNET: This slot provides Internet signal from transmitter or to transmitter.
4. RS232: Phoenix jack provides Serial port control signal from transmitter or to transmitter.
5. DC IN: Plug the 24V DC power supply into the unit.
6. IR RX: Chanel 2 IR Receiver. Connect with Wideband IR Rx.
7. IR TX: Chanel 1 IR Transmitter. Connect with Wideband IR Tx.
8. LINK LED: The connection status indicating lamp.※Flashing: The Transmitter and Receiver are in poor connections
※Dark: The Transmitter and Receiver are in no connections
※Illuminate: The Transmitter and Receiver are in good connections
9. HD BaseT IN: Standard HD BaseT signal input port. Connect HD BaseT transmitter with a UTP cable following the standard of IEEE-568A or IEEE-568B.
10. DATA LED: The data status indicating lamp.
※Flashing: The HDMI signal without HDCP.
※Dark: No HDMI signal.
※Illuminate: The HDMI signal with HDCP.

※ Description 1         POE(Power Over Ethernet) Application Example

※ Description 2         Bidirectional Infrared control Application Example

※ Description 3         Bidirectional RS232 control Application Example

※ Description 4         Bidirectional Ethernet signal Application Example

VI. Application Example